商業電器維修:5531 1921 家庭電器維修:6764 5053 維修售後支援:5445 4474
專門處理TRANSTHERM酒櫃各類疑難故障,包括時凍時唔凍、溫度飄移、不製冷、漏水、跳掣、顯示屏故障。很多客戶遇到反覆維修都修唔好,多數源於感應器、雪種洩漏、門封漏冷、壓縮機等隱藏問題。本公司位於九龍觀塘,提供上門維修及到店檢查服務。
Specialized in tricky TRANSTHERM wine‑cooler faults: intermittent cooling,temperature drift,no cooling,water leakage,trip switch,display failure.Repeated repair failures are often caused by sensor faults,refrigerant leak,door seal leak or compressor issues.Our workshop located in Kwun Tong Kowloon,we provide on‑site repair & in‑shop inspection.
原因分析:壓縮機故障、雪種洩漏、散熱塵垢過多
用戶自檢:檢查背後散熱位是否被雜物阻擋,門有冇關實
維修處理:清潔散熱網;雪種測漏加註;損壞需更換壓縮機
Cause:Compressor fault,refrigerant leak,dusty condenser
Self‑check:Check rear ventilation is not blocked,confirm door fully closed
Solution:Clean condenser;leak test & recharge refrigerant;replace faulty compressor
原因分析:溫度感應器老化、風扇循環異常、門封漏冷
用戶自檢:觀察門膠條是否有縫隙,內籠風扇有無轉動
維修處理:更換溫度感應器;維修循環風扇;替換老化門封膠條
Cause:Aging temperature sensor,faulty circulation fan,leaky door seal
Self‑check:Check door gasket gap,check inner fan rotation
Solution:Replace temperature sensor;repair fan;renew door gasket
原因分析:電源板故障、保險絲燒毀、電路接線鬆脫
用戶自檢:插座測試有冇電,電源插頭是否插穩
維修處理:檢查更換保險絲;維修電源主板;重接鬆脫線路
Cause:Power board blown,fuse burnt,loose wiring
Self‑check:Test wall socket,check power plug firmly seated
Solution:Replace fuse;repair power main‑board;reconnect loose cables
原因分析:顯示面板故障、接觸線鬆動、主板供電異常
用戶自檢:重新斷電重啟 5 分鐘再開機測試
維修處理:重新插接排線;維修或更換觸控顯示面板
Cause:Display panel failure,loom loose,main‑board power supply anomaly
Self‑check:Power off 5 minutes then restart unit
Solution:Re‑seat ribbon cable;repair / replace touch display panel
原因分析:觸摸面板受潮老化、主板控制模組損壞
用戶自檢:抹乾面板表面水氣,斷電重啟測試
維修處理:清潔檢查排線;必要更換整套觸控面板
Cause:Moisture‑damaged touch panel,damaged control module
Self‑check:Wipe moisture off panel,power‑cycle device
Solution:Inspect & clean ribbon cables;replace full touch panel assembly if needed
原因分析:門未關妥、溫度超標、故障代碼觸發警報
用戶自檢:關緊櫃門,查看屏幕有冇彈出錯誤代碼
維修處理:排除門關閉問題;讀取故障代碼維修對應零件
Cause:Door ajar,temperature over‑range,error‑code alarm trigger
Self‑check:Firmly close door,check screen for error code
Solution:Fix door‑closing;diagnose & replace parts per error‑code
原因分析:分區風扇損壞、擋風隔板移位、控溫感應器故障
用戶自檢:檢查內籠擋板有冇被酒瓶擋住出風口
維修處理:維修分區循環風扇;更換對應溫度感應器
Cause:Dual‑zone fan failure,baffle displacement,temperature sensor fault
Self‑check:Check wine bottles are not blocking air outlet baffles
Solution:Repair zone‑circulation fan;replace corresponding temperature sensor
原因分析:除霜系統失效、門封漏氣、濕度過高
用戶自檢:停機解凍,檢查門膠條有冇漏冷氣
維修處理:維修除霜感應器;更換門封膠圈
Cause:Defrost‑system failure,leaky door seal,excessive ambient humidity
Self‑check:Power‑off to defrost,inspect door gasket cold‑air leakage
Solution:Repair defrost sensor;renew door seal gasket
原因分析:排水孔堵塞、排水管脫落、凝水盤滿溢
用戶自檢:查看底部接水盤是否水滿,清理排水孔異物
維修處理:疏通排水管路;重新安裝脫落排水管
Cause:Drain hole blocked,drain pipe dislodged,overflow condensate tray
Self‑check:Check condensate tray full‑water,clear drain hole debris
Solution:Unclog drain path;re‑install fallen‑off drain pipe
原因分析:壓縮機腳膠老化、風扇葉片碰殼、零件鬆動
用戶自檢:檢查酒櫃是否擺放水平,背後有冇牆面碰撞
維修處理:更換減震膠腳;維修更換故障風扇馬達
Cause:Aging compressor rubber mount,fan blade hitting casing,loose parts
Self‑check:Check unit level,ensure no rear‑wall collision
Solution:Replace anti‑vibration feet;repair or replace defective fan motor
原因分析:門鉸磨損、門封膠條變形老化
用戶自檢:用紙張夾在門縫測試,紙可輕易抽出即漏冷
維修處理:調校門鉸;更換全新門封膠條
Cause:Worn door hinge,deformed aging door gasket
Self‑check:Paper‑gap test:paper pulls out easily = cold‑air leakage
Solution:Adjust door hinge;install brand‑new door gasket
原因分析:散熱位被封死、環境溫度太高、連續長時間運轉
用戶自檢:確保機身四周預留 10cm 以上散熱空間
維修處理:清理散熱網塵埃;改善周邊通風環境
Cause:Ventilation blocked,high ambient temperature,long‑duration continuous run
Self‑check:Keep ≥10cm clearance around unit for heat dissipation
Solution:Clean condenser dust;improve surrounding ventilation
原因分析:LED 燈條燒壞、燈具接線鬆脫
用戶自檢:斷電後輕搖燈帶位置,重啟測試
維修處理:重新接駁線路;更換 LED 照明燈條
Cause:Burnt‑out LED strip,loose lamp wiring
Self‑check:Power‑off,gently jiggle lamp strip then restart test
Solution:Reconnect wiring;replace LED lighting strip
原因分析:壓縮機短路、電容損壞、電路受潮短路
用戶自檢:不要反覆重啟,避免擴大故障
維修處理:檢測壓縮機與啟動電容,更換損壞零件
Cause:Compressor short‑circuit,damaged capacitor,moisture‑caused short‑circuit
Self‑check:Do NOT repeatedly restart to prevent further damage
Solution:Test compressor & start‑capacitor;replace defective components
原因分析:溫度探頭損壞、主板訊號異常
用戶自檢:斷電重啟,觀察是否持續亂數
維修處理:更換溫度感應探頭;檢修主控板
Cause:Damaged temperature probe,main‑board signal anomaly
Self‑check:Power‑cycle unit,observe erratic reading persistence
Solution:Replace temperature sensor probe;repair main control board
原因分析:櫃體封死散熱空間、通風位被傢俬阻擋
用戶自檢:檢查櫃體上下後方通風口是否被遮蓋
維修處理:釋放散熱空間;清潔內置散熱模組
Cause:Built‑in unit blocked ventilation,furniture covering air‑vents
Self‑check:Check top/rear/bottom vents are not covered
Solution:Release heat‑dissipation clearance;clean internal condenser module
原因分析:門封漏冷、設定溫度過低、感應器失效
用戶自檢:適當調高設定溫度,檢查櫃門密封
維修處理:更換門封膠;替換故障溫度感應器
Cause:Cold‑leaking door gasket,too‑low set‑temperature,failed sensor
Self‑check:Raise set‑temperature moderately,check door sealing status
Solution:Renew door gasket;replace defective temperature sensor
原因分析:對應感應器、風扇或主板故障
用戶自檢:斷電 5‑10 分鐘重啟,看是否消除代碼
維修處理:對應代碼排查零件,更換損壞組件
Cause:Faulty sensor / fan / main‑board corresponding to error‑code
Self‑check:Power‑off 5‑10 minutes then restart to test error reset
Solution:Troubleshoot parts per error‑code;replace damaged assembly
原因分析:除濕模組異常、門頻繁開關、環境濕度太高
用戶自檢:減少頻繁開門,檢查門密封狀態
維修處理:維修控濕零件;檢查除霜系統運作
Cause:Humidity‑control module fault,frequent door‑opening,high ambient humidity
Self‑check:Reduce frequent door‑opening,inspect door sealing condition
Solution:Repair humidity‑control components;check defrost‑system performance
原因分析:循環風扇馬達燒毀、風扇卡到異物
用戶自檢:輕聽內籠有冇風扇轉動聲音
維修處理:清理異物;維修或更換內循環風扇馬達
Cause:Burnt circulation‑fan motor,fan jammed by foreign debris
Self‑check:Listen for inner‑fan spinning noise
Solution:Clear foreign objects;repair or replace inner circulation‑fan motor
個案1|九龍塘客戶:TRANSTHERM酒櫃時凍時唔凍反覆飄移
維修前反覆找師傅維修都修唔好,檢測發現溫度感應器老化加上門封漏冷。更換感應器及全新門封膠條,溫度恢復穩定,用家非常滿意。
Case1|Kowloon Tong:TRANSTHERM wine cooler intermittent cooling
Previous repair attempts failed.Root cause:aging temperature sensor + leaky door seal.After sensor & gasket replacement,temperature stable again,customer satisfied.
個案2|淺水灣客戶:嵌入式TRANSTHERM酒櫃不製冷、底部滴水
除霜系統故障同埋排水孔長期堵塞。維修除霜零件,疏通排水系統,徹底解決結冰同漏水問題。
Case2|Repulse Bay:Built‑in TRANSTHERM no cooling & water leakage
Defrost‑system failure plus blocked drain hole.Repaired defrost components & unclog drain,ice‑build‑up & water‑leakage fully solved.
個案3|觀塘客戶:酒櫃開機跳掣,完全唔著機
壓縮機啟動電容損壞,更換電容,機器恢復正常運轉。
Case3|Kwun Tong:Wine cooler trips power & no startup
Defective compressor start‑capacitor.After capacitor replacement,unit runs normally.
香港島
中西區:中環、上環、西營盤、堅尼地城、山頂
灣仔區:灣仔、銅鑼灣、跑馬地、大坑、會展中心
東區:北角、鰂魚涌、筲箕灣、柴灣
南區:香港仔、鴨脷洲、深水灣、淺水灣、赤柱
九龍
油尖旺:油麻地、尖沙咀、旺角
深水埗:深水埗、長沙灣、荔枝角
九龍城:九龍城、九龍塘、何文田、紅磡
黃大仙:黃大仙、慈雲山、樂富、新蒲崗
觀塘:觀塘市中心、藍田、將軍澳
新界
荃灣:荃灣市區、馬灣島
屯門、元朗:元朗市區、天水圍、鄉郊
北區:上水、粉嶺、打鼓嶺
大埔:大埔墟、吐露港、船灣淡水湖
沙田:沙田市區、大圍、馬鞍山
西貢:西貢市、將軍澳
Hong Kong Island
Central‑Western,Wan Chai,Eastern,Southern districts
Kowloon
Yau Tsim Mong,Sham Shui Po,Kowloon City,Wong Tai Sin,Kwun Tong
New Territories
Tsuen Wan,Tuen Mun,Yuen Long,North District,Tai Po,Sha Tin,Sai Kung
????地址:香港九龍觀塘駿業裏10號業運工業大廈5D
????營業時間:星期一至星期六
????電話:55311921 | 67645053
????電郵:haolong2002@gmail.com
????官網:https://www.hkrepair999.com/
????Address:Flat 5D,Yip Wan Industrial Building,10 Tsun Yip Lane,Kwun Tong,Kowloon,Hong Kong
????Business Hours:Monday‑Saturday
????Tel:55311921 | 67645053
????Email:haolong2002@gmail.com
????Website:https://www.hkrepair999.com/