專業維修 Baratza 巴拉扎 咖啡研磨豆機 Professional Baratza Coffee Grinder Repair Service

成因：電源線斷裂、開關燒毀、保險絲熔斷、內部變壓器故障；檢查方式：替換插座測試、檢查機身開關、拆機檢查保險絲；維修零件：替換電源線、電源開關、保險管、變壓器。

Cause: Broken power cord, damaged power switch, blown fuse, faulty transformer. Inspection: Test different socket, check power switch, inspect internal fuse. Spare parts: power cord, power switch, fuse, transformer.

成因：咖啡豆結塊卡入刀盤、金屬異物掉入、調節刻度過緊；檢查：斷電清潔刀盤、檢查是否有螺絲/石子卡入；維修：清理異物、調整研磨間距，嚴重磨損需更換刀盤。

Cause: Clogged coffee beans, metal foreign object, too tight grind setting. Fix: Power off & clean burr, remove stuck object, adjust grind gap, replace worn burr if needed.

成因：咖啡油脂積垢、靜電吸附粉末、出粉管變形；保養：每週專用清潔片清洗，定期擦拭出粉通道；維修：疏通堵塞、更換變形出粉口套件。

Cause: Coffee oil buildup, static powder adhesion, deformed chute. Maintenance: Clean weekly with grinder cleaner tablet. Repair: Unclog chute, replace damaged chute part.

成因：刀盤齒磨損、刀盤固定螺絲鬆動、主軸間隙偏移；維修：鎖緊固定螺絲、打磨刀盤，磨損過度直接更換上下刀盤組。

Cause: Worn burr teeth, loose burr screw, shifted spindle gap. Repair: Tighten burr screw, regrind or replace full burr set.

成因：刀盤互相碰撞、軸承磨損缺油、外殼固定支架鬆動；保養：定期為軸承加注食品級潤滑油；維修：校正刀盤間距、替換磨損軸承。

Cause: Burr collision, worn dry bearing, loose housing bracket. Maintenance: Lubricate bearing with food-grade oil. Repair: Recalibrate gap, replace bearing.

成因：密封膠圈老化、出粉口卡扣鬆、機身縫隙變形；維修：替換全新密封膠圈、固定卡扣、修復變形外殼。

Cause: Aged sealing rubber ring, loose chute clip, deformed housing gap. Repair: Replace rubber seal, fasten clip, reshape casing.

成因：咖啡粉進入調節齒輪、齒輪生鏽、螺絲卡死；保養：定期拆解清潔調節機構；維修：清洗齒輪、潤滑、替換損壞調節總成。

Cause: Coffee powder jammed gear, rusted adjust gear, stuck screw. Maintenance: Disassemble & clean adjust mechanism regularly. Repair: Clean, lubricate or replace adjust assembly.

成因：計時電路板故障、感應光遮斷器髒污、馬達轉速不穩；維修：清潔光感應元件、維修主控板、替換故障計時模塊。

Cause: Faulty timer PCB, dirty optical sensor, unstable motor speed. Repair: Clean sensor, repair mainboard, replace dose module.

成因：蓋子磁吸感應器移位、彈簧開關彈力不足；維修：校正感應位置、替換彈簧觸點開關。

Cause: Misaligned magnetic sensor, weak spring limit switch. Repair: Recalibrate sensor, replace spring switch.

成因：馬達碳刷磨損、電容老化、電壓供應不足；維修：替換碳刷、啟動電容，嚴重損壞更換整組馬達。

Cause: Worn motor carbon brush, aged capacitor, insufficient voltage. Repair: Replace carbon brush & capacitor, full motor replacement if damaged.

成因：散熱孔堵塞、馬達負載過重、溫度感測器故障；保養：每月清理散熱風道；維修：清潔散熱、替換溫控感應元件。

Cause: Blocked vent, heavy motor load, faulty thermal sensor. Maintenance: Clean ventilation monthly. Repair: Clear vent, replace thermal sensor.

成因：豆倉密封圈老化、豆倉卡扣斷裂；維修：替換豆倉膠圈、更換損壞豆倉或卡扣配件。

Cause: Aged hopper seal, broken hopper clip. Repair: Replace hopper rubber seal or whole hopper clip set.

成因：面板進水受潮、觸控PCB短路、按鍵薄膜老化；維修：乾燥除濕、維修觸控電路板、替換面板總成。

Cause: Water moisture inside panel, short touch PCB, aged key film. Repair: Dry circuit, repair touch board or replace full touch panel.

成因：刀盤散熱不足、過載保護開關跳脫、馬達扭力不足；維修：升級散熱配件、替換過載保護器、更換大功率馬達。

Cause: Poor burr cooling, overload protection tripped, low torque motor. Repair: Upgrade cooling, replace overload protector, high torque motor swap.

成因：刀盤崩齒、金屬零件磨損脫屑；維修：全面拆解清潔，直接更換損壞刀盤組，禁止繼續使用。

Cause: Cracked burr tooth, worn metal spare part dropping chips. Repair: Full disassembly cleaning, replace damaged burr immediately.

保養知識：使用防靜電出粉杯、定期清洗刀盤油脂；維修升級：加裝廠商防靜電套件，更換導電出粉口。

Maintenance Tip: Use anti-static cup, clean burr oil regularly. Upgrade Repair: Install factory anti-static kit, conductive chute replacement.

成因：開關彈片氧化、電線接點鬆脫；維修：打磨開關觸點、重新焊線，損壞直接替換電源開關。

Cause: Oxidized switch spring, loose wire solder joint. Repair: Polish contact, re-solder wire or replace power switch.

成因：軸心生鏽、固定螺絲滑牙；維修：除鏽潤滑、重新攻牙鎖緊螺絲，替換損壞搖柄配件。

Cause: Rusted spindle, stripped fixing screw. Repair: Derust & lubricate, re-tap thread, replace broken crank handle.

標準保養流程：每7天使用專用清潔片研磨；每3個月完整拆解刀盤、豆倉、出粉管水洗；商用機建議每個月深度保養。

Standard Maintenance: Grind cleaner tablet weekly; full disassembly wash burr/hopper/chute every 3 months; commercial deep clean monthly.

成因：拆解後刀盤安裝偏移、調節齒輪未歸零；標準維修步驟：維修完成後執行刻度歸零校正，測試多段研磨粗細確認精度。

Cause: Misaligned burr after disassembly, un-reset adjust gear. Standard Repair Step: Zero calibration after service, test multiple grind sizes for accuracy.