A：多數係電源板燒毀、保險絲燒斷、插頭供電異常。先檢查插座有沒有電；若供電正常機器毫無反應，需要維修師傅檢測更換電源主板，全港可上門檢測。

A: Mostly burnt power board, blown fuse or abnormal wall socket power. First check whether the socket has power. If power supply is normal but unit dead, technician needs to inspect & replace main power board. Hong Kong wide on‑site inspection available.

A：常見雪種泄漏、製冷管路漏氣。壓縮機轉但無冷氣，不要長時間開機，需要師傅做管路測漏、抽真空、重新加注雪種，觀塘、九龍、新界均可上門處理。

A: Common refrigerant gas leak in cooling pipeline. Do not keep running the unit. Technician will perform leak test, vacuum pump and refrigerant recharge. On‑site service for Kwun Tong, Kowloon, New Territories.

A：E1 代表溫度感應器故障老化。感應器讀數錯亂令酒櫃無法控溫，一般直接更換對應溫度傳感器即可現場維修。

A: E1 means aged temperature sensor fault. Wrong sensor reading breaks temperature control. Usually replace temperature sensor on‑site.

A：LL 低溫報錯，多為溫度傳感器短路或者主控板訊號異常。會出現過度製冷、櫃內結厚霜，需要檢查傳感器線路及更換零件。

A: LL low‑temperature warning, caused by short‑circuited temperature sensor or main board signal error. Causes over‑cooling & thick frost. Need inspect sensor wiring & replace faulty parts.

A：HH 代表偵測到櫃內溫度過高。原因有門封漏冷、風扇不轉、冷凝器積灰散熱差、壓縮機故障。先檢查門有沒有關緊，仍然報警就要上門維修。

A: HH = detected high internal temperature. Causes: leaking door seal, broken fan, dusty condenser poor heat dissipation, compressor fault. First check door is fully closed. If alarm persists call for on‑site repair.

A：雙溫區最常壞係內循環風扇摩打損壞，冷氣無法送到另一個溫區。風扇不轉就會出現單邊不製冷，現場可以更換風扇零件。

A: Very common failure: internal circulation fan motor damaged. Cold air cannot reach second zone. Fan replacement can be done on‑site.

A：主要來源：風扇摩打磨損、壓縮機腳膠老化鬆動、管路互相撞擊。檢查是否擺放不平；噪音持續就要維修更換故障風扇或調整壓縮機避震。

A: Main sources: worn fan motor, aged compressor rubber mounts, colliding refrigerant pipes. Check unit stands level. Persistent noise needs fan replacement or compressor shock‑absorber adjustment.

A：排水孔堵塞、門封膠條老化漏冷，導致櫃外同內部大量凝露滴水。先清通排水孔；膠條老化就要更換門封，解決漏冷滴水問題。

A: Clogged drain hole or aged leaking door gasket causes heavy condensation dripping. First clear drain hole. Replace door gasket if rubber seal is worn out.

A：多為壓縮機啟動電容老化衰減，電容出力不穩，造成壓縮機斷斷續續工作。更換啟動電容多數可以解決此故障。

A: Mostly aged compressor start capacitor with unstable output, making compressor work on‑and‑off. Replacing start capacitor fixes most such faults.

A：除霜系統異常、除霜感應器故障、門密封不良濕氣持續入櫃。厚霜會阻礙製冷效果，需要維修檢查除霜感應器同主控板。

A: Defrost system malfunction, faulty defrost sensor, poor door seal letting moist air enter cabinet. Thick frost blocks cooling performance. Need inspect defrost sensor & main control board.

A：內置循環風扇摩打燒毀，就算壓縮機正常，冷氣散不出來。表現壓縮機一直轉但降溫慢，現場可更換風扇組件。

A: Burned‑out internal circulation fan motor. Compressor may run normally but cold air cannot circulate. Fan assembly can be replaced on‑site.

A：顯示面板故障或者主控板接觸不良。溫度讀數跳動無法正常設定溫度，需要檢查排線、更換顯示板或者主控電路板。

A: Defective display panel or loose main‑board wiring. Temperature readings jump and cannot set target temperature. Inspect ribbon cable; replace display board or main circuit board if needed.

A：嵌入式機型最常見散熱空間不足，後面同兩側散熱位被封死，壓縮機過熱保護。先確保機身留有散熱空位，故障依舊就要檢查壓縮機同雪種。

A: Built‑in unit frequent issue: insufficient ventilation space, blocked rear & side heat dissipation triggers compressor overheat protection. First ensure ventilation gaps. If fault persists inspect compressor & refrigerant gas.

A：壓縮機卡缸、啟動電容損壞。會聽到嗡嗡聲之後跳保護，機器無法進入製冷。需要師傅現場判斷更換電容或者壓縮機。

A: Compressor seized piston or broken start capacitor. Humming noise then safety trip, unit cannot cool. Technician on‑site diagnosis to replace capacitor or compressor.

A：aMAGIC AWC 酒櫃過保後原廠維修收費昂貴，可找專修紅酒櫃師傅，處理 E1/E3/HH/LL、不製冷、漏水、風扇、壓縮機、傳感器等故障，觀塘、九龍、香港島、新界均可提供上門檢查報價。

A: Original manufacturer repair is costly after warranty expiry. Our wine‑cooler‑specialist technicians handle E1/E3/HH/LL, no cooling, water leak, fan, compressor, sensor faults. On‑site inspection & quotation for Kwun Tong, Kowloon, Hong Kong Island & New Territories.

透過電話 / WhatsApp 講述酒櫃型號、故障現象、報錯代碼、服務地區，我地初步評估維修方向。

Tell us wine cooler model, symptoms, error codes & district via phone / WhatsApp for preliminary assessment.

雙方確認時間，師傅按約定時間前往閣下地址上門檢查。服務星期一至星期六。

Confirm appointment time. Technician visits your premise Mon‑Sat.

師傅拆解檢查，找出故障源頭，清楚講解故障同維修費用，客戶同意先會開始維修。不維修只收檢測費。

Technician diagnoses root cause, explains fault & repair cost clearly. Repair only starts after client approval. Inspection fee applies if you decline repair.

盡量現場完成維修，更換損壞零件；如需特別零件要訂貨，會再約時間二次上門。

Repair completed on‑site whenever possible. If special spare parts need ordering, we arrange return visit.

維修完畢測試製冷、溫度、顯示、風扇全部功能，確認酒櫃運作正常，交付客戶。

Full functional test for cooling, temperature reading, display & fan. Hand over to customer after normal operation confirmed.