aMAGIC AWC 酒櫃開機無風｜風扇摩打燒毀現場更換
作者：香港駿弘電器維修公司
浏览：
发表时间：2026-08-15 21:59:39
aMAGIC AWC 酒櫃維修｜開機無風｜風扇摩打燒毀現場更換
aMAGIC AWC紅酒櫃全系列故障維修服務，專門處理開機無風、風扇摩打燒毀、E1、HH、LL報錯代碼、不製冷、漏水、壓縮機損壞。本公司位於香港九龍觀塘，提供全港上門檢測、現場更換零件，無需搬機。
aMAGIC AWC 紅酒櫃 常見的問題和自已處理的解決方法
A：多數係電源板燒毀、保險絲燒斷、插頭供電異常。先檢查插座有沒有電；若供電正常機器毫無反應，需要維修師傅檢測更換電源主板，全港可上門檢測。
A：常見雪種泄漏、製冷管路漏氣。壓縮機轉但無冷氣，不要長時間開機，需要師傅做管路測漏、抽真空、重新加注雪種，觀塘、九龍、新界均可上門處理。
A：E1 代表溫度感應器故障老化。感應器讀數錯亂令酒櫃無法控溫，一般直接更換對應溫度傳感器即可現場維修。
A：LL 低溫報錯，多為溫度傳感器短路或者主控板訊號異常。會出現過度製冷、櫃內結厚霜，需要檢查傳感器線路及更換零件。
A：HH 代表偵測到櫃內溫度過高。原因有門封漏冷、風扇不轉、冷凝器積灰散熱差、壓縮機故障。先檢查門有沒有關緊，仍然報警就要上門維修。
A：雙溫區最常壞係內循環風扇摩打損壞，冷氣無法送到另一個溫區。風扇不轉就會出現單邊不製冷，現場可以更換風扇零件。
A：主要來源：風扇摩打磨損、壓縮機腳膠老化鬆動、管路互相撞擊。檢查是否擺放不平；噪音持續就要維修更換故障風扇或調整壓縮機避震。
A：排水孔堵塞、門封膠條老化漏冷，導致櫃外同內部大量凝露滴水。先清通排水孔；膠條老化就要更換門封，解決漏冷滴水問題。
A：多為壓縮機啟動電容老化衰減，電容出力不穩，造成壓縮機斷斷續續工作。更換啟動電容多數可以解決此故障。
A：除霜系統異常、除霜感應器故障、門密封不良濕氣持續入櫃。厚霜會阻礙製冷效果，需要維修檢查除霜感應器同主控板。
A：內置循環風扇摩打燒毀，就算壓縮機正常，冷氣散不出來。表現壓縮機一直轉但降溫慢，現場可更換風扇組件。
A：顯示面板故障或者主控板接觸不良。溫度讀數跳動無法正常設定溫度，需要檢查排線、更換顯示板或者主控電路板。
A：嵌入式機型最常見散熱空間不足，後面同兩側散熱位被封死，壓縮機過熱保護。先確保機身留有散熱空位，故障依舊就要檢查壓縮機同雪種。
A：壓縮機卡缸、啟動電容損壞。會聽到嗡嗡聲之後跳保護，機器無法進入製冷。需要師傅現場判斷更換電容或者壓縮機。
A：aMAGIC AWC 酒櫃過保後原廠維修收費昂貴，可找專修紅酒櫃師傅，處理 E1/E3/HH/LL、不製冷、漏水、風扇、壓縮機、傳感器等故障，觀塘、九龍、香港島、新界均可提供上門檢查報價。
維修工具介紹
數位萬用電表
檢測電源板、感應器、風扇摩打、壓縮機通斷與電壓。
雪種測漏儀
檢測製冷管路雪種泄漏位置，精準定位漏點。
真空泵及雪種加注機
管路抽真空，重新加注雪種，恢復製冷能力。
溫度測試儀
比對酒櫃實際溫度同顯示溫度，判斷感應器故障。
電子焊台
維修電源板、主控板電子零件焊接。
成套拆卸工具組
拆裝酒櫃外殼、風扇、冷凝器、門封膠條。
酒櫃上門維修流程
客戶查詢報價
WhatsApp / 電話聯絡，講述酒櫃故障、型號、地址，預約上門時間。
師傅上門到場
按約定時間到達現場，不須客戶搬動重型酒櫃。
全面故障檢測
檢查電源板、風扇摩打、壓縮機、溫度感應器、製冷管路，確認故障位置。
報價確認
向客戶講解故障原因、維修方案、零件費用，客戶同意才開始維修。
現場維修更換零件
現場更換風扇摩打、傳感器、電源板、電容、雪種加注等，大部份故障當場完成。
測試機器運作
維修完畢運行測試，確認製冷、風扇、顯示、報警全部正常。
完工交付
向客戶講解使用保養注意事項，維修完成。
成功個案 客戶好評
★★★★★
「aMAGIC AWC酒櫃完全無風，風扇摩打燒毀，師傅觀塘上門，現場更換風扇，半個鐘搞掂，價錢合理。」
— 觀塘客戶
★★★★★
「酒櫃彈出E1故障代碼，溫度控制亂晒，更換溫度感應器之後恢復正常，不用搬機非常方便。」
— 九龍塘客戶
★★★★★
「雙溫區酒櫃一邊唔凍，檢查發現風扇摩打壞咗，師傅新界沙田上門現場維修，效果滿意。」
— 沙田客戶
★★★★★
「酒櫃HH高溫報警不停響，冷凝器積灰同風扇故障，處理完之後溫度回復正常。」
— 香港島灣仔客戶
可維修電器品牌
維諾卡夫、芭克斯、哈士奇、西門子、美的、海爾、卡薩帝、索菲亞、新朝、富客等品牌專屬服務
aMAGIC AWC、electrolux伊莱克斯、德国宝、Asko、Baumatic、Bosch、Wino、Candy 金鼎、Canopus 肯特、Comfee、Fisher & Paykel 飛雪、Fujira 日本富士樂、Gaggenau、Gala 家麗牌、German Home、Hitachi 日立、Kaneda 金田、LG 樂金、MI 小米、Midea 美的、Miele、Panasonic 樂聲、Philco 飛歌、Rasonic 樂信、Samsung 三星、Sharp 聲寶、Siemens 西門子、Smeg、Speed Queen、Summe 德國卓爾、Thomson、Toshiba 東芝、V‑Zug、Vestel、Whirlpool 惠而浦、White‑Westinghouse 威士汀、Zanussi 金章、FOTILE 方太、米卡Mia Cucina、苏泊尔SUPOR、老板Robam、德瑪仕DEMASHI、志高CHIGO、樂創Lecon、卡士Couss、UKOEO、海氏Hauswirt、長帝Changdi
服務地區｜全港上門維修
- 香港島
- 中西區：中環、上環、西營盤、堅尼地城、山頂
- 灣仔區：灣仔、銅鑼灣、跑馬地、大坑、會展中心
- 東區：北角、鰂魚涌、筲箕灣、柴灣
- 南區：香港仔、鴨脷洲、深水灣、淺水灣、赤柱
- 九龍
- 油尖旺：油麻地、尖沙咀、旺角
- 深水埗：深水埗、長沙灣、荔枝角
- 九龍城：九龍城、九龍塘、何文田、紅磡
- 黃大仙：黃大仙、慈雲山、樂富、新蒲崗
- 觀塘：觀塘市中心、藍田、將軍澳
- 新界
- 荃灣：荃灣市區、馬灣島
- 屯門、元朗：元朗市區、天水圍、鄉郊
- 北區：上水、粉嶺、打鼓嶺
- 大埔：大埔墟、吐露港、船灣淡水湖
- 沙田：沙田市區、大圍、馬鞍山
- 西貢：西貢市、將軍澳
聯絡我們
地址：香港九龍觀塘駿業裏10號業運工業大廈5D
營業時間：星期一至星期六
聯絡電話：55311921 ｜ 67645053
官網網站：https://www.hkrepair999.com/
社交平台
aMAGIC AWC Wine Cooler Repair｜No Wind On Startup｜On‑site Fan Motor Replacement
Professional on‑site repair service for aMAGIC AWC wine cooler series. Fix no‑fan issue, burnt fan motor, E1 HH LL error codes, no cooling, water leakage, compressor failure. Our workshop is located in Kwun Tong Kowloon, Hong Kong. On‑site inspection & component replacement all over Hong Kong, no need to move your heavy wine chiller.
aMAGIC AWC Wine Cooler Common Faults & Self‑troubleshooting
A：Mostly caused by burnt power board, blown fuse or wall socket supply failure. First check whether wall socket has power. If power supply is normal but unit no response, technician needs to inspect and replace main power board. On‑site inspection available across Hong Kong.
A：Commonly refrigerant gas leakage on cooling pipeline. Do NOT keep machine running long time. Technician will perform leak test, vacuum pumping and refrigerant re‑charge. On‑site service for Kwun Tong, Kowloon, New Territories.
A：E1 means temperature sensor aging & fault. Wrong sensor reading causes temperature control failure. On‑site replacement of temperature sensor can resolve the issue.
A：LL low‑temperature alarm. Usually short‑circuited temperature sensor or main board signal error. Unit will over‑cool and build thick frost. Need inspect sensor wiring and replace faulty parts.
A：HH alarm means inside cabinet temperature too high. Causes include broken door seal, non‑rotating fan, dusty condenser poor heat dissipation or compressor fault. First check door fully closed. If alarm persists please arrange on‑site repair.
A：Most frequent failure: internal circulation fan motor damaged. Cold air cannot circulate to second zone. On‑site fan motor component replacement service.
A：Sources: worn fan motor, aged compressor rubber mount, pipeline collision. Check if unit placed level. If noise remains, replace defective fan or adjust compressor shock‑absorbing parts.
A：Drain hole blockage or aged door seal letting cold air escape, causing heavy condensation. Clear drain hole first. Replace door seal if rubber gasket is worn out.
A：Aged compressor start capacitor with unstable output makes compressor work intermittently. Replacing start capacitor can fix most of such cases.
A：Defrost system malfunction, faulty defrost sensor or bad door seal letting humid air enter cabinet. Thick frost blocks cooling performance. Technician needs inspect defrost sensor and main control board.
A：Burnt internal circulation fan motor. Compressor may run normally but cold air cannot circulate. Compressor keeps running yet temperature drops very slowly. Fan assembly can be replaced on‑site.
A：Faulty display panel or bad connection on main board. Temperature reading jumps and cannot set target temperature normally. Need inspect ribbon cable, replace display board or main circuit board.
A：Built‑in model often lacks heat‑dissipation clearance. Side & rear ventilation space blocked triggers compressor overheat protection. Make sure ventilation gap reserved. If fault continues inspect compressor and refrigerant.
A：Compressor seized or damaged start capacitor. Humming sound then safety cut‑off. Technician onsite assessment for capacitor replacement or compressor replacement.
A：Original manufacturer out‑of‑warranty service charge is expensive. Our specialist fix E1/E3/HH/LL error, no cooling, leakage, fan & compressor & sensor faults. On‑site inspection & quotation for Hong Kong Island, Kowloon, Kwun Tong and New Territories.
Repair Tools Introduction
Digital Multimeter
Test power board, sensor, fan motor and compressor voltage & continuity.
Refrigerant Leak Detector
Locate refrigerant leakage point on cooling pipeline accurately.
Vacuum Pump & Refrigerant Charger
Pipeline vacuum pumping and refrigerant re‑fill to restore cooling capacity.
Temperature Tester
Compare real cabinet temperature vs display reading to judge sensor fault.
Soldering Station
Electronic component soldering for power board & main controller board.
Disassembly Tool Kit
Dismantle cabinet shell, fan unit, condenser and door seal gasket.
On‑site Repair Workflow
Customer Enquiry & Quotation
Contact via WhatsApp / phone, describe fault, model and address, book appointment time.
Technician Arrive On‑site
Arrive on scheduled time, no need customer to move heavy wine cooler.
Full Fault Diagnosis
Inspect power board, fan motor, compressor, temperature sensor and cooling pipeline, locate root cause.
Quotation Confirmation
Explain fault reason, repair plan and parts cost. Repair only after customer approval.
On‑site Repair & Parts Replacement
Replace fan motor, sensor, power board, capacitor, recharge refrigerant. Most faults finished same visit.
Machine Operation Test
Full running test, verify cooling, fan rotation, display and alarm function all normal.
Work Completed
Explain maintenance tips for customer, job finished.
Successful Cases & Customer Reviews
★★★★★
“aMAGIC AWC wine cooler no wind, fan motor burnt. Technician came Kwun Tong on‑site, replaced fan within 30 mins, price reasonable.”
— Customer in Kwun Tong
★★★★★
“E1 error code temperature out‑of‑control, replaced temperature sensor, works perfectly, no need to transport heavy unit.”
— Customer in Kowloon Tong
★★★★★
“Dual‑zone cooler one side not cold, fan motor broken. On‑site repair in Sha Tin New Territories, result satisfied.”
— Customer in Sha Tin
★★★★★
“HH high‑temperature alarm beeping non‑stop, dusty condenser plus fan fault. Temperature back to normal after servicing.”
— Customer in Wan Chai Hong Kong Island
Brands We Repair
aMAGIC AWC, electrolux, German Pool, Asko, Baumatic, Bosch, Wino, Candy, Canopus, Comfee, Fisher & Paykel, Fujira, Gaggenau, Gala, German Home, Hitachi, Kaneda, LG, MI, Midea, Miele, Panasonic, Philco, Rasonic, Samsung, Sharp, Siemens, Smeg, Speed Queen, Summe, Thomson, Toshiba, V‑Zug, Vestel, Whirlpool, White‑Westinghouse, Zanussi, FOTILE, Mia Cucina, SUPOR, Robam, DEMASHI, CHIGO, Lecon, Couss, UKOEO, Hauswirt, Changdi and more.
Service Coverage｜On‑site Repair Whole Hong Kong
- Hong Kong Island
- Central & Western: Central, Sheung Wan, Sai Ying Pun, Kennedy Town, The Peak
- Wan Chai: Wan Chai, Causeway Bay, Happy Valley, Tai Hang, HKCEC
- Eastern: North Point, Quarry Bay, Shau Kei Wan, Chai Wan
- Southern: Aberdeen, Ap Lei Chau, Deep Water Bay, Repulse Bay, Stanley
- Kowloon
- Yau Tsim Mong: Yau Ma Tei, Tsim Sha Tsui, Mong Kok
- Sham Shui Po: Sham Shui Po, Cheung Sha Wan, Lai Chi Kok
- Kowloon City: Kowloon City, Kowloon Tong, Ho Man Tin, Hung Hom
- Wong Tai Sin: Wong Tai Sin, Tsz Wan Shan, Lok Fu, San Po Kong
- Kwun Tong: Kwun Tong Central, Lam Tin, Tseung Kwan O
- New Territories
- Tsuen Wan: Tsuen Wan, Ma Wan
- Tuen Mun, Yuen Long: Yuen Long town, Tin Shui Wai, rural area
- North District: Sheung Shui, Fanling, Ta Kwu Ling
- Tai Po: Tai Po Market, Tolo Harbour, Plover Cove
- Sha Tin: Sha Tin, Tai Wai, Ma On Shan
- Sai Kung: Sai Kung Town, Tseung Kwan O
Contact Us
Address: 5D, Yau Wan Industrial Building, 10 Chun Yip Lane, Kwun Tong, Kowloon, Hong Kong
Business Hours: Monday to Saturday
Phone: 55311921 ｜ 67645053
Email: haolong2002@gmail.com
Official Website: https://www.hkrepair999.com/
