Wino 酒櫃顯示 LL 低溫故障代碼｜溫度傳感器損壞維修更換｜香港上門維修

Wino 酒櫃顯示 LL 低溫故障代碼｜溫度傳感器損壞維修更換

Wino 紅酒櫃常見故障維修服務，處理 LL、E1、HH 各類報錯代碼、不製冷、結霜、漏水、風扇故障、壓縮機問題。本公司位於香港九龍觀塘，提供全港上門檢測維修。

WhatsApp 查詢維修致電 55311921 致電 67645053

Wino 紅酒櫃常見的問題和自已處理的解決方法

A：多數係電源板燒毀、保險絲燒斷、插頭供電異常。先檢查插座有沒有電；若供電正常機器毫無反應，需要維修師傅檢測更換電源主板，全港可上門檢測。

A：常見雪種泄漏、製冷管路漏氣。壓縮機轉但無冷氣，不要長時間開機，需要師傅做管路測漏、抽真空、重新加注雪種，觀塘、九龍、新界均可上門處理。

A：E1 代表溫度感應器故障老化。感應器讀數錯亂令酒櫃無法控溫，一般直接更換對應溫度傳感器即可現場維修。

A：LL 低溫報錯，多為溫度傳感器短路或者主控板訊號異常。會出現過度製冷、櫃內結厚霜，需要檢查傳感器線路及更換零件。

A：HH 代表偵測到櫃內溫度過高。原因有門封漏冷、風扇不轉、冷凝器積灰散熱差、壓縮機故障。先檢查門有沒有關緊，仍然報警就要上門維修。

A：雙溫區最常壞係內循環風扇摩打損壞，冷氣無法送到另一個溫區。風扇不轉就會出現單邊不製冷，現場可以更換風扇零件。

A：主要來源：風扇摩打磨損、壓縮機腳膠老化鬆動、管路互相撞擊。檢查是否擺放不平；噪音持續就要維修更換故障風扇或調整壓縮機避震。

A：排水孔堵塞、門封膠條老化漏冷，導致櫃外同內部大量凝露滴水。先清通排水孔；膠條老化就要更換門封，解決漏冷滴水問題。

A：多為壓縮機啟動電容老化衰減，電容出力不穩，造成壓縮機斷斷續續工作。更換啟動電容多數可以解決此故障。

A：除霜系統異常、除霜感應器故障、門密封不良濕氣持續入櫃。厚霜會阻礙製冷效果，需要維修檢查除霜感應器同主控板。

A：內置循環風扇摩打燒毀，就算壓縮機正常，冷氣散不出來。表現壓縮機一直轉但降溫慢，現場可更換風扇組件。

A：顯示面板故障或者主控板接觸不良。溫度讀數跳動無法正常設定溫度，需要檢查排線、更換顯示板或者主控電路板。

A：嵌入式機型最常見散熱空間不足，後面同兩側散熱位被封死，壓縮機過熱保護。先確保機身留有散熱空位，故障依舊就要檢查壓縮機同雪種。

A：壓縮機卡缸、啟動電容損壞。會聽到嗡嗡聲之後跳保護，機器無法進入製冷。需要師傅現場判斷更換電容或者壓縮機。

A：Wino 酒櫃過保後原廠維修收費昂貴，可找專修紅酒櫃師傅，處理 E1/E3/HH/LL、不製冷、漏水、風扇、壓縮機、傳感器等故障，觀塘、九龍、香港島、新界均可提供上門檢查報價。

維修工具介紹

製冷維修工具

雪種壓力錶、真空泵、測漏儀，專用於酒櫃管路測漏、抽真空、加注雪種。

電子檢測儀器

萬用電表、溫度傳感器測試儀，檢測電源板、主控板、感應器線路故障。

拆卸維修工具

專用套筒、撬殼工具，安全拆開酒櫃外殼，更換風扇、電容、門封膠條。

標準維修流程

客戶WhatsApp/電話講述故障症狀，初步評估問題
師傅預約時間，上門到場檢查機器
檢測故障點，向客戶報價維修費用
客戶確認後，現場維修、更換損壞零件
測試機器運行，確認故障排除
完成維修，交付客戶

成功個案與客戶好評

個案1｜Wino酒櫃 LL低溫報錯

客戶酒櫃顯示LL，櫃內嚴重結霜。檢測發現溫度傳感器短路，現場更換傳感器，機器恢復正常控溫。

客戶評價：師傅上門準時，很快解決LL故障，價格合理。

個案2｜Wino雙溫區酒櫃單邊不凍

一區溫度正常，另一區完全不製冷。確認內循環風扇摩打損壞，現場更換風扇組件，雙溫區恢復製冷。

客戶評價：解決雙溫區一邊唔凍問題，技術專業。

個案3｜Wino酒櫃壓縮機轉但不製冷

壓縮機持續運轉，溫度降不下。檢測管路雪種洩漏，做測漏、抽真空、重新加注雪種，故障修復。

客戶評價：處理雪種泄漏，酒櫃而家可以正常保存紅酒。

我們維修的酒櫃電器品牌

維諾卡夫、芭克斯、哈士奇、西門子、美的、海爾、卡薩帝、索菲亞、新朝、富客等品牌專屬服務

Electrolux伊莱克斯德國宝 Asko Baumatic Bosch Wino Candy 金鼎 Canopus 肯特 Comfee Fisher & Paykel 飛雪 Fujira 日本富士樂 Gaggenau Gala 家麗牌 German Home Hitachi 日立 Kaneda 金田 LG 樂金 MI 小米 Midea 美的 Miele Panasonic 樂聲 Philco 飛歌 Rasonic 樂信 Samsung 三星 Sharp 聲寶 Siemens 西門子 Smeg Summe 德國卓爾 Toshiba 東芝 Whirlpool 惠而浦 Zanussi 金章 FOTILE 方太 Mia Cucina米卡 SUPOR苏泊尔

服務地區｜全港上門維修

香港島

中西區：中環、上環、西營盤、堅尼地城、山頂
灣仔區：灣仔、銅鑼灣、跑馬地、大坑、會展中心
東區：北角、鰂魚涌、筲箕灣、柴灣
南區：香港仔、鴨脷洲、深水灣、淺水灣、赤柱

九龍

油尖旺：油麻地、尖沙咀、旺角
深水埗：深水埗、長沙灣、荔枝角
九龍城：九龍城、九龍塘、何文田、紅磡
黃大仙：黃大仙、慈雲山、樂富、新蒲崗
觀塘區：觀塘市中心、藍田、將軍澳

新界

荃灣：荃灣市區、馬灣島
屯門、元朗：元朗市區、天水圍
北區：上水、粉嶺、打鼓嶺
大埔：大埔墟、吐露港、船灣淡水湖
沙田：沙田、大圍、馬鞍山
西貢：西貢市、將軍澳

聯絡資訊

地址：香港九龍觀塘駿業裏10號業運工業大廈5D

工作時間：星期一至星期六

聯絡電話：55311921｜67645053

電郵：haolong2002@gmail.com

官方網站：https://www.hkrepair999.com/

Wino Wine Cabinet LL Low‑Temperature Error Code｜Temperature Sensor Repair & Replacement

Wino wine cabinet repair LL error code sensor replacement

Professional Wino wine cabinet repair service in Hong Kong. Fix LL, E1, HH error codes, no cooling, frosting, water leakage, fan & compressor faults. On‑site service for Hong Kong Island, Kowloon & New Territories. Workshop located in Kwun Tong Kowloon.

WhatsApp Enquiry Call 55311921 Call 67645053

Wino Wine Cabinet Common Problems & Self‑Troubleshooting

A: Usually burnt power board, blown fuse or power supply fault. First check wall socket power. If power supply normal but unit dead, technician needs to inspect & replace power motherboard. On‑site inspection available all over Hong Kong.

A: Refrigerant gas leakage on cooling pipeline. Do not keep machine running long. Need leak test, vacuum pumping and refrigerant re‑charge. Kwun Tong, Kowloon, New Territories on‑site service.

A: E1 means temperature sensor aging or failure. Sensor reading error causes temperature control failure. On‑site replacement of temperature sensor normally solves problem.

A: LL low‑temperature alarm, mostly sensor short‑circuit or main board signal error. Causes over‑cooling & heavy frost. Need inspect sensor wiring and replace defective parts.

A: HH alarm means detected internal temperature too high. Possible causes: door seal leak, fan failure, dusty condenser poor heat dissipation, compressor fault. Check door closed properly first, still alarm requires on‑site repair.

A: Most common fault: internal circulation fan motor damaged. Cold air cannot circulate to second zone. Fan motor replacement can fix on‑site.

A: Fan motor wear, aged compressor rubber mount, pipeline collision. Check unit level placement. Persistent noise needs fan replacement or compressor shock‑absorb adjustment.

A: Drain hole blocked or aged door seal causing cold leakage & heavy condensation. Clear drain hole first. Replace door seal rubber if seal aging.

A: Compressor start capacitor aging. Capacitor unstable output makes compressor work on‑off intermittently. Replace start capacitor for most cases.

A: Defrost system fault, defrost sensor failure or bad door seal letting moisture enter cabinet. Heavy frost blocks cooling effect. Need inspect defrost sensor & main control board.

A: Built‑in circulation fan motor burnt out. Compressor runs but cold air cannot spread. Slow temperature drop symptom. Fan assembly replacement on‑site.

A: Display panel failure or loose main‑board wiring. Cannot set temperature normally. Need inspect wiring harness, replace display panel or main circuit board.

A: Built‑in model common issue: insufficient heat‑dissipation clearance blocked causing compressor overheat protection. Leave enough ventilation space. If fault remains inspect compressor & refrigerant.

A: Compressor stuck rotor or damaged start capacitor. Humming sound then protection trip. Technician on‑site diagnose replace capacitor or compressor.

A: Original manufacturer repair charge high after warranty. We specialise wine cabinet repair for E1/E3/HH/LL error, no‑cooling, leakage, fan, compressor & sensor faults. On‑site inspection & quotation for Kwun Tong, Kowloon, Hong Kong Island, New Territories.

Repair Tools Introduction

Refrigeration Tools

Refrigerant gauge set, vacuum pump, leak detector, used for pipeline leak test, vacuum pumping and refrigerant re‑charging.

Electronic Testing Equipment

Multimeter, temperature sensor tester, diagnose power board, main board and sensor wiring faults.

Disassembly Hand Tools

Special sockets & pry tools for safe cabinet teardown, replace fan motor, capacitor and door seal rubber.

Standard Repair Workflow

Customer describe fault via WhatsApp / phone for preliminary assessment
Book appointment, technician arrive on‑site
Inspect machine, provide repair quotation to client
After customer confirmation, repair & replace broken parts on‑site
Test full operation to confirm fault resolved
Complete repair and hand over to customer

Successful Repair Cases & Customer Reviews

Case 1｜Wino LL low‑temperature error

LL error heavy frost inside cabinet. Fault: short‑circuited temperature sensor. On‑site sensor replacement, temperature control restored normal.

Customer review: Technician arrived punctually, solved LL fault quickly, reasonable price.

Case 2｜Dual‑zone one compartment no cooling

One zone normal cold, second zone zero cooling. Damaged internal circulation fan motor. Replace fan assembly restore dual‑zone cooling function.

Customer review: Fixed single‑side no‑cooling problem, professional workmanship.

Case3｜Compressor running but zero cooling

Compressor keep running, cabinet temperature not dropping. Refrigerant gas leakage detected. Leak test, vacuum & refrigerant refill completed, machine fully functional.

Customer review: Fixed refrigerant leakage, wine cabinet works fine for wine storage now.

Supported Appliance Brands For Repair

Electrolux German Pool Asko Bosch Wino Midea Miele Panasonic Samsung Sharp Siemens Smeg Toshiba Whirlpool Zanussi

Service Coverage｜On‑site Repair All Hong Kong

Hong Kong Island

Central & Western: Central, Sheung Wan, Sai Ying Pun, Kennedy Town, The Peak
Wan Chai: Wan Chai, Causeway Bay, Happy Valley, Tai Hang
Eastern: North Point, Quarry Bay, Shau Kei Wan, Chai Wan
Southern: Aberdeen, Ap Lei Chau, Deep Water Bay, Repulse Bay, Stanley

Kowloon

Yau Tsim Mong: Yau Ma Tei, Tsim Sha Tsui, Mong Kok
Sham Shui Po: Sham Shui Po, Cheung Sha Wan, Lai Chi Kok
Kowloon City: Kowloon City, Kowloon Tong, Ho Man Tin, Hung Hom
Wong Tai Sin: Wong Tai Sin, Tsz Wan Shan, Lok Fu, San Po Kong
Kwun Tong: Kwun Tong, Lam Tin, Tseung Kwan O

New Territories

Tsuen Wan: Tsuen Wan, Ma Wan
Tuen Mun, Yuen Long: Yuen Long, Tin Shui Wai
North District: Sheung Shui, Fanling, Ta Kwu Ling
Tai Po: Tai Po Market, Tolo Harbour
Sha Tin: Sha Tin, Tai Wai, Ma On Shan
Sai Kung: Sai Kung Town, Tseung Kwan O

Contact Information

Address: 5D, Yau Wan Industrial Building, 10 Chun Yip Lane, Kwun Tong, Kowloon, Hong Kong

Business Hours: Monday‑Saturday

Phone: 55311921 | 67645053

Email: haolong2002@gmail.com

Official Website:https://www.hkrepair999.com/