Vinorich 酒櫃漏水滴水維修｜香港上門處理積水漏水問題
作者：香港駿弘電器維修公司
浏览：
发表时间：2026-08-08 21:49:13
Vinorich酒櫃20個常見故障｜問題與處理方案
20 Common Vinorich Wine Cooler Faults & Troubleshooting
原因分析 / Cause：壓縮機故障、雪種洩漏、散熱塵垢過多
Compressor failure, refrigerant leak, dirty heat‑dissipating coil
Compressor failure, refrigerant leak, dirty heat‑dissipating coil
用戶自檢 / Self‑check：檢查背後散熱位是否被雜物阻擋，門有冇關實
Check rear ventilation is not blocked, confirm door fully closed
Check rear ventilation is not blocked, confirm door fully closed
維修處理 / Repair：清潔散熱網；雪種測漏加註；損壞需更換壓縮機
Clean condenser coil; leak test & recharge refrigerant; replace faulty compressor
Clean condenser coil; leak test & recharge refrigerant; replace faulty compressor
原因分析 / Cause：溫度感應器老化、風扇循環異常、門封漏冷
Aged temperature sensor, circulation fan defect, door seal cold‑air leakage
Aged temperature sensor, circulation fan defect, door seal cold‑air leakage
用戶自檢 / Self‑check：觀察門膠條是否有縫隙，內籠風扇有無轉動
Check door gasket gap, listen for inner fan rotation
Check door gasket gap, listen for inner fan rotation
維修處理 / Repair：更換溫度感應器；維修循環風扇；替換老化門封膠條
Replace temp sensor; repair circulation fan; renew door gasket
Replace temp sensor; repair circulation fan; renew door gasket
原因分析 / Cause：電源板故障、保險絲燒毀、電路接線鬆脫
Faulty power board, blown fuse, loose wiring
Faulty power board, blown fuse, loose wiring
用戶自檢 / Self‑check：插座測試有冇電，電源插頭是否插穩
Test wall socket power, check plug connection
Test wall socket power, check plug connection
維修處理 / Repair：檢查更換保險絲；維修電源主板；重接鬆脫線路
Inspect & replace fuse; repair main power board; re‑secure loose wiring
Inspect & replace fuse; repair main power board; re‑secure loose wiring
原因分析 / Cause：顯示面板故障、接觸線鬆動、主板供電異常
Defective display panel, loose ribbon cable, mainboard power anomaly
Defective display panel, loose ribbon cable, mainboard power anomaly
用戶自檢 / Self‑check：重新斷電重啟 5 分鐘再開機測試
Power off for 5 minutes then restart unit
Power off for 5 minutes then restart unit
維修處理 / Repair：重新插接排線；維修或更換觸控顯示面板
Reconnect ribbon cable; repair / replace touch‑display module
Reconnect ribbon cable; repair / replace touch‑display module
原因分析 / Cause：觸摸面板受潮老化、主板控制模組損壞
Moisture‑damaged touch panel, defective main control module
Moisture‑damaged touch panel, defective main control module
用戶自檢 / Self‑check：抹乾面板表面水氣，斷電重啟測試
Wipe moisture off panel, power‑cycle unit
Wipe moisture off panel, power‑cycle unit
維修處理 / Repair：清潔檢查排線；必要更換整套觸控面板
Clean & inspect ribbon cable; replace full touch‑panel assembly if needed
Clean & inspect ribbon cable; replace full touch‑panel assembly if needed
原因分析 / Cause：門未關妥、溫度超標、故障代碼觸發警報
Door not fully closed, over‑temperature, fault‑code trigger alarm
Door not fully closed, over‑temperature, fault‑code trigger alarm
用戶自檢 / Self‑check：關緊櫃門，查看屏幕有冇彈出錯誤代碼
Firmly close door, check screen for error code
Firmly close door, check screen for error code
維修處理 / Repair：排除門關閉問題；讀取故障代碼維修對應零件
Resolve door closure issue; diagnose & replace faulty component per error code
Resolve door closure issue; diagnose & replace faulty component per error code
原因分析 / Cause：分區風扇損壞、擋風隔板移位、控溫感應器故障
Damaged zone fan, displaced baffle, defective zone temperature sensor
Damaged zone fan, displaced baffle, defective zone temperature sensor
用戶自檢 / Self‑check：檢查內籠擋板有冇被酒瓶擋住出風口
Check wine bottles are not blocking air baffle & vents
Check wine bottles are not blocking air baffle & vents
維修處理 / Repair：維修分區循環風扇；更換對應溫度感應器
Repair zone circulation fan; replace faulty zone temperature sensor
Repair zone circulation fan; replace faulty zone temperature sensor
原因分析 / Cause：除霜系統失效、門封漏氣、濕度過高
Failed defrost system, leaking door gasket, excessive ambient humidity
Failed defrost system, leaking door gasket, excessive ambient humidity
用戶自檢 / Self‑check：停機解凍，檢查門膠條有冇漏冷氣
Power‑off to defrost unit; inspect door gasket cold‑air leakage
Power‑off to defrost unit; inspect door gasket cold‑air leakage
維修處理 / Repair：維修除霜感應器；更換門封膠圈
Repair defrost sensor; replace door gasket seal
Repair defrost sensor; replace door gasket seal
原因分析 / Cause：排水孔堵塞、排水管脫落、凝水盤滿溢
Clogged drain hole, disconnected drain tube, overflow condensate tray
Clogged drain hole, disconnected drain tube, overflow condensate tray
用戶自檢 / Self‑check：查看底部接水盤是否水滿，清理排水孔異物
Check condensate tray water level, clear debris from drain hole
Check condensate tray water level, clear debris from drain hole
維修處理 / Repair：疏通排水管路；重新安裝脫落排水管
Unclog drain pipeline; reinstall disconnected drain hose
Unclog drain pipeline; reinstall disconnected drain hose
原因分析 / Cause：壓縮機腳膠老化、風扇葉片碰殼、零件鬆動
Aged compressor rubber mount, fan blade hitting casing, loose components
Aged compressor rubber mount, fan blade hitting casing, loose components
用戶自檢 / Self‑check：檢查酒櫃是否擺放水平，背後有冇牆面碰撞
Check unit level installation; ensure rear not touching wall
Check unit level installation; ensure rear not touching wall
維修處理 / Repair：更換減震膠腳；維修更換故障風扇馬達
Replace anti‑vibration feet; repair or replace defective fan motor
Replace anti‑vibration feet; repair or replace defective fan motor
原因分析 / Cause：門鉸磨損、門封膠條變形老化
Worn door hinges, deformed & aged door gasket
Worn door hinges, deformed & aged door gasket
用戶自檢 / Self‑check：用紙張夾在門縫測試，紙可輕易抽出即漏冷
Paper slip test on door gap; easy pull‑out indicates cold‑air leakage
Paper slip test on door gap; easy pull‑out indicates cold‑air leakage
維修處理 / Repair：調校門鉸；更換全新門封膠條
Adjust door hinges; install brand‑new door gasket
Adjust door hinges; install brand‑new door gasket
原因分析 / Cause：散熱位被封死、環境溫度太高、連續長時間運轉
Blocked ventilation, high ambient temperature, prolonged continuous running
Blocked ventilation, high ambient temperature, prolonged continuous running
用戶自檢 / Self‑check：確保機身四周預留 10cm 以上散熱空間
Keep minimum 10 cm clearance all around cabinet for ventilation
Keep minimum 10 cm clearance all around cabinet for ventilation
維修處理 / Repair：清理散熱網塵埃；改善周邊通風環境
Clean dust on condenser coil; improve surrounding air circulation
Clean dust on condenser coil; improve surrounding air circulation
原因分析 / Cause：LED 燈條燒壞、燈具接線鬆脫
Burn‑out LED strip, loose light wiring
Burn‑out LED strip, loose light wiring
用戶自檢 / Self‑check：斷電後輕搖燈帶位置，重啟測試
Power‑off, gently nudge light strip then restart unit
Power‑off, gently nudge light strip then restart unit
維修處理 / Repair：重新接駁線路；更換 LED 照明燈條
Reconnect wiring harness; replace LED light strip
Reconnect wiring harness; replace LED light strip
原因分析 / Cause：壓縮機短路、電容損壞、電路受潮短路
Compressor short‑circuit, faulty capacitor, moisture‑caused short‑circuit
Compressor short‑circuit, faulty capacitor, moisture‑caused short‑circuit
用戶自檢 / Self‑check：不要反覆重啟，避免擴大故障
Do NOT repeatedly restart unit to prevent further damage
Do NOT repeatedly restart unit to prevent further damage
維修處理 / Repair：檢測壓縮機與啟動電容，更換損壞零件
Test compressor & run‑capacitor, replace defective components
Test compressor & run‑capacitor, replace defective components
原因分析 / Cause：溫度探頭損壞、主板訊號異常
Damaged temperature probe, abnormal signal from main control board
Damaged temperature probe, abnormal signal from main control board
用戶自檢 / Self‑check：斷電重啟，觀察是否持續亂數
Power‑cycle unit and observe display behaviour
Power‑cycle unit and observe display behaviour
維修處理 / Repair：更換溫度感應探頭；檢修主控板
Replace temperature sensor probe; service main control board
Replace temperature sensor probe; service main control board
原因分析 / Cause：櫃體封死散熱空間、通風位被傢俬阻擋
Zero ventilation clearance, furniture blocking air vents
Zero ventilation clearance, furniture blocking air vents
用戶自檢 / Self‑check：檢查櫃體上下後方通風口是否被遮蓋
Check top / rear / bottom vents are not blocked
Check top / rear / bottom vents are not blocked
維修處理 / Repair：釋放散熱空間；清潔內置散熱模組
Restore ventilation clearance; clean built‑in heat dissipation module
Restore ventilation clearance; clean built‑in heat dissipation module
原因分析 / Cause：門封漏冷、設定溫度過低、感應器失效
Cold leakage via door gasket, overly low set temperature, failed sensor
Cold leakage via door gasket, overly low set temperature, failed sensor
用戶自檢 / Self‑check：適當調高設定溫度，檢查櫃門密封
Raise set temperature moderately; inspect door seal condition
Raise set temperature moderately; inspect door seal condition
維修處理 / Repair：更換門封膠；替換故障溫度感應器
Replace door gasket; swap defective temperature sensor
Replace door gasket; swap defective temperature sensor
原因分析 / Cause：對應感應器、風扇或主板故障
Faulty related sensor, fan or mainboard component
Faulty related sensor, fan or mainboard component
用戶自檢 / Self‑check：斷電 5‑10 分鐘重啟，看是否消除代碼
Power‑off 5‑10 minutes then restart to clear temporary fault
Power‑off 5‑10 minutes then restart to clear temporary fault
維修處理 / Repair：對應代碼排查零件，更換損壞組件
Diagnose per error‑code specification; replace defective assembly
Diagnose per error‑code specification; replace defective assembly
原因分析 / Cause：除濕模組異常、門頻繁開關、環境濕度太高
Defective dehumidify module, frequent door opening, high ambient humidity
Defective dehumidify module, frequent door opening, high ambient humidity
用戶自檢 / Self‑check：減少頻繁開門，檢查門密封狀態
Reduce frequent door opening, inspect door sealing performance
Reduce frequent door opening, inspect door sealing performance
維修處理 / Repair：維修控濕零件；檢查除霜系統運作
Repair humidity‑control parts; verify defrost‑system function
Repair humidity‑control parts; verify defrost‑system function
原因分析 / Cause：循環風扇馬達燒毀、風扇卡到異物
Burn‑out circulation fan motor, foreign object jamming fan blade
Burn‑out circulation fan motor, foreign object jamming fan blade
用戶自檢 / Self‑check：輕聽內籠有冇風扇轉動聲音
Listen carefully for inner fan spinning noise
Listen carefully for inner fan spinning noise
維修處理 / Repair：清理異物；維修或更換內循環風扇馬達
Remove jammed debris; repair / replace inner circulation fan motor
Remove jammed debris; repair / replace inner circulation fan motor
支援維修酒櫃電器品牌
Supported Wine Cooler Brands For Repair
維諾卡夫 Vinorich
芭克斯哈士奇西門子 Siemens
美的 Midea海爾卡薩帝索菲亞
新朝富客Electrolux伊莱克斯
German宝AskoBoschSmeg
Whirlpool惠而浦MielePanasonic樂聲
Samsung三星Sharp聲寶LG樂金
小米 MIGaggenauZanussi金章
FOTILE方太Canopus肯特Rasonic樂信
Toshiba東芝Summe德國卓爾
維修工具介紹｜維修流程步驟
Repair Tools & Standard Working Procedure
維修工具圖片位置 Repair tools image
專業維修工具
雪種測漏儀、溫度探頭測試儀、萬用電表、管道疏通工具、除霜檢測儀、電子測溫槍，精準定位酒櫃漏水、電路、製冷故障。
Professional Repair Tools
Refrigerant leak detector, multi‑meter, thermal probe tester, drain‑pipe cleaner, infrared thermometer, for accurate diagnosis of leak, electric & cooling faults.
維修流程圖 Repair workflow image
標準維修順序
1.客戶報價諮詢 → 2.上門 / 送機到觀塘工廈檢測 → 3.故障定位報價 →4.客戶確認後維修更換零件 →5.測試機器運行 →6.交付及售後跟進
Standard Repair Steps
1. Customer enquiry & quotation →2. On‑site / Kwun Tong workshop inspection →3. Fault diagnosis & quote →4. Repair & part replacement upon confirmation →5. Full function testing →6. Hand‑over & after‑sales follow‑up
成功個案｜客戶好評
Successful Cases & Customer Testimonials
香港服務地區｜全港上門維修
Service Coverage Across Hong Kong
香港島 Hong Kong Island
中西區：中環、上環、西營盤、堅尼地城、山頂
灣仔區：灣仔、銅鑼灣、跑馬地、大坑、會展
東區：北角、鰂魚涌、筲箕灣、柴灣
南區：香港仔、鴨脷洲、深水灣、淺水灣、赤柱
九龍 Kowloon
油尖旺：油麻地、尖沙咀、旺角
深水埗：深水埗、長沙灣、荔枝角
九龍城：九龍城、九龍塘、何文田、紅磡
黃大仙：黃大仙、慈雲山、樂富、新蒲崗
觀塘：觀塘市中心、藍田、將軍澳
新界 New Territories
荃灣、馬灣
屯門、元朗、天水圍
北區：上水、粉嶺、打鼓嶺
大埔、沙田、大圍、馬鞍山
西貢、將軍澳
聯絡我們｜Contact Us
???? 地址：香港九龍觀塘駿業裏10號業運工業大廈5D
???? 工作時間：星期一至星期六
???? WhatsApp：點擊直接對話 Chat Now
???? 電郵：haolong2002@gmail.com
???? 官網：https://www.hkrepair999.com/
Contact Information
???? Address: Unit 5D, Yau Wan Industrial Building, 10 Tsun Yip Lane, Kwun Tong, Kowloon, Hong Kong
???? Business Hours: Monday‑Saturday
???? Tel: +852 55311921｜+852 67645053
???? WhatsApp: Click to chat directly
???? Email: haolong2002@gmail.com
???? Official Site: https://www.hkrepair999.com/
文章推荐
