維修 De'Longhi 德龙咖啡機 Edica Art | 各种商用咖啡全系列生产工具支援，駿弘電器維修用心守護你的咖啡機
作者：香港駿弘電器維修公司
浏览：
发表时间：2026-07-26 12:47:54
駿弘電器維修
Chun Hong Electrical Repair
維修De'Longhi 德龍咖啡機 Eletta Art｜商用咖啡設備維修
De'Longhi Eletta Art Coffee Machine Repair | Commercial Coffee Equipment Service
De'Longhi Eletta Art 20大常見故障維修Q&A
20 Common Faults for De'Longhi Eletta Art Q&A
Q1德龍咖啡機機底漏水、滴水盤經常積水，是什麼問題？Machine bottom leaking, drip tray fills quickly
+
故障現象：沖洗或製作咖啡時機身底部滲水，滴水盤短時間就積滿水。
故障原因：矽膠軟管老化破裂、沖煮組密封圈硬化、熱交換器積垢滲漏、水箱底部止水閥損壞。
自行檢查方法：檢查水箱底膠閥狀態、定期拆解清洗沖煮組、執行完整除垢程序。
維修更換零件：矽膠水管、沖煮組密封圈、水箱底止水閥。
故障原因：矽膠軟管老化破裂、沖煮組密封圈硬化、熱交換器積垢滲漏、水箱底部止水閥損壞。
自行檢查方法：檢查水箱底膠閥狀態、定期拆解清洗沖煮組、執行完整除垢程序。
維修更換零件：矽膠水管、沖煮組密封圈、水箱底止水閥。
Symptom: Water leaks under machine during rinse/brewing, drip tray fills rapidly.
Causes: Aged silicone tube crack, brew group seal hardened, heat exchanger scale leakage, tank bottom valve damaged.
Self-check: Inspect tank valve, clean brew group regularly, complete descaling cycle.
Replacement Parts: Silicone tube, brew group gasket, tank shut-off valve.
Causes: Aged silicone tube crack, brew group seal hardened, heat exchanger scale leakage, tank bottom valve damaged.
Self-check: Inspect tank valve, clean brew group regularly, complete descaling cycle.
Replacement Parts: Silicone tube, brew group gasket, tank shut-off valve.
Q2水箱有水，但機器持續閃缺水提示 FILL TANK，如何維修？Tank full but machine shows FILL TANK warning
+
故障現象：水箱已經加滿清水，儀表仍然提示缺水，有時做完一杯咖啡立刻報警。
故障原因：水位浮子卡滯或破損、水流感應器故障、水箱接觸位髒汙導致感應失靈。
自行檢查方法：取出水箱清洗水位浮球，擦乾機身與水箱接觸觸點。
維修更換零件：水位浮子總成、水流傳感器（水表）。
故障原因：水位浮子卡滯或破損、水流感應器故障、水箱接觸位髒汙導致感應失靈。
自行檢查方法：取出水箱清洗水位浮球，擦乾機身與水箱接觸觸點。
維修更換零件：水位浮子總成、水流傳感器（水表）。
Symptom: Water tank full yet "FILL TANK" alert appears, triggers after single shot.
Causes: Stuck/broken float, flow sensor failure, dirty contact points.
Self-check: Remove tank, clean float ball, wipe contact terminals.
Replacement Parts: Float assembly, flow meter sensor.
Causes: Stuck/broken float, flow sensor failure, dirty contact points.
Self-check: Remove tank, clean float ball, wipe contact terminals.
Replacement Parts: Float assembly, flow meter sensor.
Q3德龍咖啡機磨豆機不轉、卡豆、研磨時發出異響？Grinder not spinning, stuck beans, abnormal noise
+
故障現象：切換咖啡豆模式，磨豆馬達沒有反應，或是出現金屬異響，無法正常下豆研磨。
故障原因：咖啡豆油脂黏附刀盤造成堵塞、異物卡入刀盤、磨豆馬達燒毀、傳動齒輪卡阻。
自行檢查方法：清空豆倉清理咖啡油垢，禁止空機狀態調校研磨粗細。
維修更換零件：磨豆馬達、磨豆刀盤、研磨傳動齒輪。
故障原因：咖啡豆油脂黏附刀盤造成堵塞、異物卡入刀盤、磨豆馬達燒毀、傳動齒輪卡阻。
自行檢查方法：清空豆倉清理咖啡油垢，禁止空機狀態調校研磨粗細。
維修更換零件：磨豆馬達、磨豆刀盤、研磨傳動齒輪。
Symptom: Grinder motor no response, metal noise, unable grind coffee beans.
Causes: Oil residue block burrs, foreign object jam, burnt motor, jammed gear.
Self-check: Empty hopper, clean coffee grease. Do not adjust grind while empty.
Replacement Parts: Grinder motor, burr set, drive gear.
Causes: Oil residue block burrs, foreign object jam, burnt motor, jammed gear.
Self-check: Empty hopper, clean coffee grease. Do not adjust grind while empty.
Replacement Parts: Grinder motor, burr set, drive gear.
Q4咖啡出水量不穩定，同一設定有時多、有時少？Unstable coffee output volume with same setting
+
故障現象：固定咖啡份量設定，萃取水量忽多忽少，無法穩定定量。
故障原因：水流感應器老化、內部水路水垢堵塞、水泵壓力衰退。
自行檢查方法：執行完整除垢，多次啟動自動沖洗清理水路。
維修更換零件：水流感應水表、電磁閥、震動水泵。
故障原因：水流感應器老化、內部水路水垢堵塞、水泵壓力衰退。
自行檢查方法：執行完整除垢，多次啟動自動沖洗清理水路。
維修更換零件：水流感應水表、電磁閥、震動水泵。
Symptom: Inconsistent shot volume under identical settings.
Causes: Aging flow sensor, limescale blockage, weak pump pressure.
Self-check: Full descaling, run auto rinse repeatedly.
Replacement Parts: Flow meter, solenoid valve, vibration pump.
Causes: Aging flow sensor, limescale blockage, weak pump pressure.
Self-check: Full descaling, run auto rinse repeatedly.
Replacement Parts: Flow meter, solenoid valve, vibration pump.
Q5沖出來的咖啡不夠熱、出水溫度偏低怎麼處理？Coffee temperature too low, insufficient heat
+
故障現象：機器顯示備妥 READY，但咖啡溫度偏涼，蒸汽溫度不足。
故障原因：NTC 溫度感應器故障、加熱熱塊堆積大量水垢、溫控保護跳脫。
自行檢查方法：善用預沖洗功能、定期除鈣、萃取前預熱咖啡杯。
維修更換零件：NTC 溫度探針、加熱熱塊、熱保護器。
故障原因：NTC 溫度感應器故障、加熱熱塊堆積大量水垢、溫控保護跳脫。
自行檢查方法：善用預沖洗功能、定期除鈣、萃取前預熱咖啡杯。
維修更換零件：NTC 溫度探針、加熱熱塊、熱保護器。
Symptom: Machine READY but coffee cool, weak steam temperature.
Causes: Faulty NTC sensor, scale blocked thermoblock, thermal protection tripped.
Self-check: Pre-rinse, regular descaling, preheat cups.
Replacement Parts: NTC probe, thermoblock, thermal fuse protector.
Causes: Faulty NTC sensor, scale blocked thermoblock, thermal protection tripped.
Self-check: Pre-rinse, regular descaling, preheat cups.
Replacement Parts: NTC probe, thermoblock, thermal fuse protector.
Q6咖啡機無法產生蒸汽、蒸汽出力弱，只有熱水沒有蒸氣？No steam, weak steam, only hot water from steam wand
+
故障現象：切換蒸汽模式，只能流出熱水，產生不了蒸汽，難以打奶泡。
故障原因：蒸汽管路水垢淤塞、蒸汽電磁閥卡滯、水泵壓力不足、蒸汽噴嘴堵塞。
自行檢查方法：拆解清洗蒸汽棒，定期執行完整除垢程序。
維修更換零件：蒸汽電磁閥、蒸汽噴嘴套件、水泵。
故障原因：蒸汽管路水垢淤塞、蒸汽電磁閥卡滯、水泵壓力不足、蒸汽噴嘴堵塞。
自行檢查方法：拆解清洗蒸汽棒，定期執行完整除垢程序。
維修更換零件：蒸汽電磁閥、蒸汽噴嘴套件、水泵。
Symptom: Steam mode outputs hot water only, cannot foam milk.
Causes: Scale clogged steam path, stuck steam solenoid, low pump pressure, blocked nozzle.
Self-check: Disassemble & clean steam wand, full descaling cycle.
Replacement Parts: Steam solenoid, steam nozzle kit, water pump.
Causes: Scale clogged steam path, stuck steam solenoid, low pump pressure, blocked nozzle.
Self-check: Disassemble & clean steam wand, full descaling cycle.
Replacement Parts: Steam solenoid, steam nozzle kit, water pump.
Q7自動奶泡系統打出奶泡稀薄、泡沫粗大，吸奶管不吸牛奶？Auto milk frother weak foam, suction tube no milk intake
+
故障現象：卡布奇諾系統噴濺、奶泡容易消散，吸管無法抽取牛奶。
故障原因：奶泡管路、奶泡頭累積奶垢堵塞、進氣孔封閉。
自行檢查方法：每次使用完即清洗整套奶泡配件，拆解沖洗所有管路。
維修更換零件：奶泡吸管、奶泡頭、奶泡閥組。
故障原因：奶泡管路、奶泡頭累積奶垢堵塞、進氣孔封閉。
自行檢查方法：每次使用完即清洗整套奶泡配件，拆解沖洗所有管路。
維修更換零件：奶泡吸管、奶泡頭、奶泡閥組。
Symptom: Splatters, unstable foam, milk suction failure.
Causes: Milk residue block tube, air inlet blocked.
Self-check: Clean all milk components after every use.
Replacement Parts: Milk suction tube, frother head, milk valve assembly.
Causes: Milk residue block tube, air inlet blocked.
Self-check: Clean all milk components after every use.
Replacement Parts: Milk suction tube, frother head, milk valve assembly.
Q8機器出現三角形嘆號、GENERAL ALARM 通用故障警報？Triangle warning sign, GENERAL ALARM error
+
故障現象：螢幕亮起通用故障警示，無法製作咖啡。
故障原因：沖煮組位置偏移、傳動馬達卡滯、機內過髒、主板訊號異常。
自行檢查方法：斷電關機，取出沖煮組清潔後重新正確安裝。
維修更換零件：沖煮組傳動馬達、位置感應開關。
故障原因：沖煮組位置偏移、傳動馬達卡滯、機內過髒、主板訊號異常。
自行檢查方法：斷電關機，取出沖煮組清潔後重新正確安裝。
維修更換零件：沖煮組傳動馬達、位置感應開關。
Symptom: General alarm triggered, machine stops brewing.
Causes: Misaligned brew group, jam drive motor, dirty interior, mainboard signal error.
Self-check: Power off, remove, clean and reinstall brew group.
Replacement Parts: Brew group drive motor, position sensor switch.
Causes: Misaligned brew group, jam drive motor, dirty interior, mainboard signal error.
Self-check: Power off, remove, clean and reinstall brew group.
Replacement Parts: Brew group drive motor, position sensor switch.
Q9沖煮組（萃取器）卡住，沒辦法取出，硬拉會損壞嗎？Brew group stuck, cannot be pulled out
+
故障現象：無法拉出沖煮組，關機之後仍然卡緊。
故障原因：沖煮組停留在非拆卸位置、咖啡粉結塊卡阻、傳動齒輪磨損。
自行檢查方法：務必在完全斷電狀態嘗試取出，禁止強行拉扯。
維修更換零件：沖煮組總成、傳動齒輪組。
故障原因：沖煮組停留在非拆卸位置、咖啡粉結塊卡阻、傳動齒輪磨損。
自行檢查方法：務必在完全斷電狀態嘗試取出，禁止強行拉扯。
維修更換零件：沖煮組總成、傳動齒輪組。
Symptom: Brew group locked, unable to remove after power off.
Causes: Group not at service position, compacted coffee powder, worn drive gear.
Self-check: Fully power off first, NEVER pull hard manually.
Replacement Parts: Complete brew group, drive gear set.
Causes: Group not at service position, compacted coffee powder, worn drive gear.
Self-check: Fully power off first, NEVER pull hard manually.
Replacement Parts: Complete brew group, drive gear set.
Q10咖啡一滴一滴緩慢流出、萃取速度很慢，咖啡味道苦澀？Slow dripping coffee, bitter over-extraction
+
故障現象：出水細小呈滴漏狀，萃取時間過長。
故障原因：水路水垢、咖啡出水口噴嘴堵塞；半自動機型常見濾碗堵塞、沖煮頭膠圈積垢。
自行檢查方法：清理出水口噴嘴、完整除垢，嘗試調粗研磨度測試。
維修更換零件：出水噴嘴、電磁閥。
故障原因：水路水垢、咖啡出水口噴嘴堵塞；半自動機型常見濾碗堵塞、沖煮頭膠圈積垢。
自行檢查方法：清理出水口噴嘴、完整除垢，嘗試調粗研磨度測試。
維修更換零件：出水噴嘴、電磁閥。
Symptom: Slow drip, overly long extraction time, bitter taste.
Causes: Limescale & clogged spout, portafilter clog for semi-auto models.
Self-check: Clean spout, full descaling, try coarser grind.
Replacement Parts: Coffee spout nozzle, solenoid valve.
Causes: Limescale & clogged spout, portafilter clog for semi-auto models.
Self-check: Clean spout, full descaling, try coarser grind.
Replacement Parts: Coffee spout nozzle, solenoid valve.
Q11雙出水口只有單邊出咖啡，另一邊完全不出水？Dual spout only one side dispenses coffee
+
故障現象：咖啡機雙噴嘴其中一側沒有咖啡流出。
故障原因：噴嘴累積乾硬咖啡油垢造成堵塞。
自行檢查方法：使用軟刷小心清理噴孔，養成定期沖洗習慣。
維修更換零件：咖啡出水口噴嘴總成。
故障原因：噴嘴累積乾硬咖啡油垢造成堵塞。
自行檢查方法：使用軟刷小心清理噴孔，養成定期沖洗習慣。
維修更換零件：咖啡出水口噴嘴總成。
Symptom: One spout dry, only single side pour coffee.
Causes: Dried coffee grease blocks nozzle hole.
Self-check: Soft brush clean spout, regular rinse routine.
Replacement Parts: Dual coffee spout assembly.
Causes: Dried coffee grease blocks nozzle hole.
Self-check: Soft brush clean spout, regular rinse routine.
Replacement Parts: Dual coffee spout assembly.
Q12廢渣盒咖啡渣不多，卻持續提示需要清空渣盒？Small coffee waste triggers empty waste box alert
+
故障現象：少量咖啡渣就觸發滿渣警示，不能繼續製作咖啡。
故障原因：渣盒光感感應窗口髒汙、彈簧觸點開關老化。
自行檢查方法：擦拭渣盒感應窗口、清潔滴水盤觸點。
維修更換零件：光感感應器、彈簧觸點開關。
故障原因：渣盒光感感應窗口髒汙、彈簧觸點開關老化。
自行檢查方法：擦拭渣盒感應窗口、清潔滴水盤觸點。
維修更換零件：光感感應器、彈簧觸點開關。
Symptom: Waste box alert even with minimal coffee puck.
Causes: Dirty optical sensor window, worn contact switch.
Self-check: Wipe sensor window & drip tray contacts.
Replacement Parts: Optical sensor, spring contact switch.
Causes: Dirty optical sensor window, worn contact switch.
Self-check: Wipe sensor window & drip tray contacts.
Replacement Parts: Optical sensor, spring contact switch.
Q13水泵嗡嗡震動噪音很大，但是完全不出水？Pump loud humming, zero water output
+
故障現象：按下萃取鍵，水泵持續發出噪音，沒有水流產生。
故障原因：水路出現空氣鎖、水泵老化、進水濾網堵塞、電磁閥卡死。
自行檢查方法：開啟熱水功能排出管路空氣，檢查水箱進水濾網。
維修更換零件：震動水泵、進水濾網、電磁閥。
故障原因：水路出現空氣鎖、水泵老化、進水濾網堵塞、電磁閥卡死。
自行檢查方法：開啟熱水功能排出管路空氣，檢查水箱進水濾網。
維修更換零件：震動水泵、進水濾網、電磁閥。
Symptom: Pump hums loudly, no water flows out.
Causes: Air lock, aging pump, blocked inlet filter, stuck solenoid.
Self-check: Run hot water to purge air, clean inlet filter.
Replacement Parts: Vibration pump, inlet filter, solenoid valve.
Causes: Air lock, aging pump, blocked inlet filter, stuck solenoid.
Self-check: Run hot water to purge air, clean inlet filter.
Replacement Parts: Vibration pump, inlet filter, solenoid valve.
Q14面板按鍵失靈、燈號亂閃，機器會自動執行沖洗？Control panel unresponsive, random flashing lights
+
故障現象：觸控或實體按鍵沒有反應，有時候自行觸發指令。
故障原因：操作面板受潮、按鍵膜老化、面板排線氧化。
自行檢查方法：斷電靜置半小時，等待機身內部除濕。
維修更換零件：操作面板、面板連接排線。
故障原因：操作面板受潮、按鍵膜老化、面板排線氧化。
自行檢查方法：斷電靜置半小時，等待機身內部除濕。
維修更換零件：操作面板、面板連接排線。
Symptom: Buttons no response, random auto rinse trigger.
Causes: Moisture inside panel, aged membrane, oxidized cable.
Self-check: Power off and rest 30 mins to dehumidify.
Replacement Parts: Control panel, ribbon cable.
Causes: Moisture inside panel, aged membrane, oxidized cable.
Self-check: Power off and rest 30 mins to dehumidify.
Replacement Parts: Control panel, ribbon cable.
Q15咖啡機閒置時不停自動沖洗，耗費大量清水？Continuous auto rinse while idle, waste water
+
故障現象：開機、閒置階段持續自動沖水，無法停止。
故障原因：主板程式異常、溫度感應訊號不穩、水流感應器誤判。
自行檢查方法：斷電重啟，嘗試回復機器出廠設定。
維修更換零件：主控板、NTC 溫度感應器。
故障原因：主板程式異常、溫度感應訊號不穩、水流感應器誤判。
自行檢查方法：斷電重啟，嘗試回復機器出廠設定。
維修更換零件：主控板、NTC 溫度感應器。
Symptom: Machine keeps auto rinsing during standby.
Causes: Mainboard firmware error, unstable NTC, false flow sensor reading.
Self-check: Power cycle, restore factory settings.
Replacement Parts: Main control board, NTC temperature sensor.
Causes: Mainboard firmware error, unstable NTC, false flow sensor reading.
Self-check: Power cycle, restore factory settings.
Replacement Parts: Main control board, NTC temperature sensor.
Q16EC685、EC9335 半自動機，把手周圍噴水漏水？EC685 / EC9335 semi-auto leak around portafilter
+
故障現象：萃取時不從濾碗出水，把手外圍噴濺咖啡。
故障原因：沖煮頭密封圈老化硬化、堆積咖啡垢失去密封性。
自行檢查方法：拆出沖煮頭密封圈清洗觀察彈性。
維修更換零件：沖煮頭密封圈（沖煮頭膠圈）。
故障原因：沖煮頭密封圈老化硬化、堆積咖啡垢失去密封性。
自行檢查方法：拆出沖煮頭密封圈清洗觀察彈性。
維修更換零件：沖煮頭密封圈（沖煮頭膠圈）。
Symptom: Water splashes outside portafilter instead of pouring from basket.
Causes: Hardened group head gasket covered by coffee residue.
Self-check: Remove gasket and inspect elasticity after cleaning.
Replacement Parts: Group head rubber gasket.
Causes: Hardened group head gasket covered by coffee residue.
Self-check: Remove gasket and inspect elasticity after cleaning.
Replacement Parts: Group head rubber gasket.
Q17預磨粉通道堵塞，使用咖啡粉模式無法正常萃取？Pre-ground coffee chute blocked, cannot brew powder coffee
+
故障現象：倒入咖啡粉不會落入沖煮組，咖啡味道偏淡甚至不出咖啡。
故障原因：粉槽累積油垢結塊，封閉進粉通道。
自行檢查方法：使用專用毛刷定期清理預磨粉通道。
維修更換零件：預磨粉導料通道套件。
故障原因：粉槽累積油垢結塊，封閉進粉通道。
自行檢查方法：使用專用毛刷定期清理預磨粉通道。
維修更換零件：預磨粉導料通道套件。
Symptom: Pre-ground coffee stuck in chute, weak or zero output.
Causes: Oil residue caking blocks powder channel.
Self-check: Regular brush clean pre-ground chute.
Replacement Parts: Pre-ground coffee feed chute assembly.
Causes: Oil residue caking blocks powder channel.
Self-check: Regular brush clean pre-ground chute.
Replacement Parts: Pre-ground coffee feed chute assembly.
Q18除垢程式無法完成，一直重複提醒需要除垢？Descaling cycle incomplete, descale alert persists
+
故障現象：跑完整套除垢流程，警示燈仍然持續閃爍。
故障原因：機內水垢過厚、除垢期間水位不足、水流感應計數異常。
自行檢查方法：除垢時水箱加水至 MAX 刻度，重新完整執行一次除垢。
維修更換零件：水流感應水表。
故障原因：機內水垢過厚、除垢期間水位不足、水流感應計數異常。
自行檢查方法：除垢時水箱加水至 MAX 刻度，重新完整執行一次除垢。
維修更換零件：水流感應水表。
Symptom: Descaling finished yet warning light keeps flashing.
Causes: Excessive scale, insufficient water during cycle, flow meter counting error.
Self-check: Fill tank to MAX and redo full descaling.
Replacement Parts: Flow sensor meter.
Causes: Excessive scale, insufficient water during cycle, flow meter counting error.
Self-check: Fill tank to MAX and redo full descaling.
Replacement Parts: Flow sensor meter.
Q19運作途中自動斷電、無預警關機，擱置一段時間才能重啟？Machine auto power off mid-operation, rest required to restart
+
故障現象：製作咖啡中途機器突然熄機，無法立刻開機。
故障原因：熱保護器過熱跳脫、主板供電故障、整流橋損壞。
自行檢查方法：機器保留散熱空間，不要緊貼牆壁擺放。
維修更換零件：熱保護保險絲、主板整流橋、電源板。
故障原因：熱保護器過熱跳脫、主板供電故障、整流橋損壞。
自行檢查方法：機器保留散熱空間，不要緊貼牆壁擺放。
維修更換零件：熱保護保險絲、主板整流橋、電源板。
Symptom: Unexpected power cut during brewing, cannot restart immediately.
Causes: Thermal protector tripped, power board fault, broken rectifier bridge.
Self-check: Keep ventilation space, avoid placing against wall.
Replacement Parts: Thermal fuse, rectifier bridge, power supply board.
Causes: Thermal protector tripped, power board fault, broken rectifier bridge.
Self-check: Keep ventilation space, avoid placing against wall.
Replacement Parts: Thermal fuse, rectifier bridge, power supply board.
Q20萃取咖啡 crema 薄、味道偏淡，香氣不足？Thin crema, weak flavour, low aroma
+
故障現象：相同咖啡豆與研磨設定，咖啡口感如水，crema 稀少。
故障原因：磨豆刀盤磨損變鈍、水路輕微堵塞、沖煮組密封失效。
自行檢查方法：微調至更細研磨度測試，全面清洗沖煮組。
維修更換零件：磨豆刀盤、沖煮組密封圈。
故障原因：磨豆刀盤磨損變鈍、水路輕微堵塞、沖煮組密封失效。
自行檢查方法：微調至更細研磨度測試，全面清洗沖煮組。
維修更換零件：磨豆刀盤、沖煮組密封圈。
Symptom: Watery espresso, thin crema under same grind & bean setting.
Causes: Worn grinder burrs, minor waterway blockage, leaky brew group seal.
Self-check: Try finer grind, fully clean brew group.
Replacement Parts: Grinder burr set, brew group gasket.
Causes: Worn grinder burrs, minor waterway blockage, leaky brew group seal.
Self-check: Try finer grind, fully clean brew group.
Replacement Parts: Grinder burr set, brew group gasket.
維修品牌｜商用/家用咖啡研磨機、咖啡機維修
Brands We Repair | Commercial & Home Coffee Grinders & Machines
Mahlkönig 迈赫迪（德國）
EK43、E65S、E80、K30、VTA、GH1
Ditting 迪廷（瑞士）
KR807、807 LabSweet、1203
Victoria Arduino 黑鷹（意大利）
Mythos One、MY75、MY85、M1
Mazzer 馬扎
Super Jolly、Mini、Robur S、ZM、Kony
La Marzocco 辣媽（意大利）
Pico
Eureka 尤里卡
Olympus、Mignon系列、Grinta
Fiorenzato 佛倫薩多
F64E、F83E、F74
Nuova Simonelli 諾瓦
MCF 商用磨豆機
Compak 康派克（西班牙）
E6、F10、R12
WPM 惠家
ZD10、ZD12、ZD15、ZD17N、ZD18、ZD21
Delonghi 德龍｜Sage 鉑富副線
全自動、半自動咖啡機系列
Breville 鉑富
BCG820、BCG600
同時維修：格米莱、泰摩、漢匠、Comandante、Hario、Baratza、Panasonic、Wilfa 等全系列咖啡研磨設備
We also service Gemilai, Timemore, Hanjiang, Comandante, Hario, Baratza, Panasonic, Wilfa and more coffee grinders.
香港服務地區
Hong Kong Service Coverage
香港島
Hong Kong Island
中西區、灣仔區、東區、南區
中環、上環、西營盤、銅鑼灣、北角、柴灣、香港仔、赤柱
Central & Western, Wan Chai, Eastern, Southern District
九龍
Kowloon
油尖旺、深水埗、九龍城、黃大仙、觀塘
尖沙咀、旺角、長沙灣、紅磡、觀塘、藍田
Yau Tsim Mong, Sham Shui Po, Kowloon City, Wong Tai Sin, Kwun Tong
新界
New Territories
荃灣、屯門、元朗、上水、大埔、沙田、西貢、將軍澳
Tsuen Wan, Tuen Mun, Yuen Long, Sheung Shui, Tai Po, Sha Tin, Sai Kung, Tseung Kwan O
聯絡駿弘電器維修
Contact Chun Hong Electrical Repair
門市地址：香港九龍觀塘駿業裏10號業運工業大廈5D
Shop Address: 5D, Yip Wan Industrial Building, 10 Chun Yip Lane, Kwun Tong, Kowloon, Hong Kong
營業時間：星期一至星期六
Opening Hours: Monday to Saturday
電話：+852 55311921 ｜ +852 67645053
Email：haolong2002@gmail.com
