駿弘電器維修

故障成因：電源線斷裂、保險絲燒毀、開關元件損壞、馬達過熱保護鎖定、插座接觸不良
保養/檢查：更換插座測試、檢查電源線外層破損、定期清理散熱口
維修方案：更換保險絲、維修電源開關、重繞/替換磨豆機馬達

Cause: Broken power cord, blown fuse, faulty power switch, motor overheat lock, loose socket
Check & Maintain: Test different socket, inspect cord damage, clean heat vent regularly
Repair: Replace fuse, fix power switch, rewind or replace motor

傳動齒輪磨損、皮帶斷裂、連接軸滑牙、咖啡豆卡死刀盤間隙
維修：更換傳動齒輪/皮帶、拆解清理卡豆、重製連接軸

Worn drive gear, broken belt, stripped shaft gear, coffee beans stuck between burrs
Repair: Replace gear/belt, disassemble clean stuck beans, repair drive shaft

刀盤變形、刀齒磨平、調節盤移位、上下刀盤間隙不平衡、進料口偏位
保養：每3個月清潔刀盤；維修：打磨或替換鋼刀盤、校正調節座

Deformed burr, dull cutting teeth, shifted adjustment dial, uneven burr gap, misaligned hopper
Maintain: Clean burr every 3 months; Repair: Polish or replace burr, realign adjustment base

刀盤鬆動、軸承磨損、金屬雜質掉入刀盤、馬達軸心偏移、防震膠老化
維修：加固刀盤固定螺絲、更換軸承、拆解清除金屬碎屑、更換防震墊

Loose burr, worn bearing, metal debris trapped, offset motor shaft, aged anti-vibration rubber
Repair: Tighten burr screw, replace bearing, remove metal debris, new anti-vibration pad

咖啡油脂殘留結塊、濕氣受潮、出粉通道變窄、靜電吸附嚴重
保養：每次使用完清潔粉道；維修：拆解高溫清洗通道、安裝靜電消除配件

Built-up coffee oil, moisture block, narrow chute, heavy static cling
Maintain: Clean chute after every use; Repair: Disassemble deep clean, install static eliminator

調節螺紋積油卡灰、調節齒輪崩齒、定位彈簧斷裂、刻度盤滑牙
維修：拆解清洗螺紋、替換齒輪與彈簧、重製調節刻度結構

Grease & dust jammed thread, broken adjustment gear, snapped spring, stripped dial gear
Repair: Deep clean thread, replace gear & spring, rebuild adjustment mechanism

馬達線圈老化過熱、溫度感應保護器故障、電路板短路、散熱孔堵塞
維修：更換溫控保護、維修驅動電路板、清理散熱系統、重繞馬達線圈

Aged motor coil overheat, faulty thermal protector, short circuit board, blocked vent
Repair: Replace thermal fuse, fix circuit board, clean cooling system, rewind motor coil

環境乾燥、粉道塑膠材質、缺少靜電導流配件、刀盤間隙過細
保養：使用除靜電噴霧；維修：加裝金屬導流靜電片、替換粉道內襯

Dry environment, plastic chute, missing static strip, too fine grind gap
Maintain: Anti-static spray; Repair: Install metal static strip, replace chute lining

豆倉膠圈老化硬化、蓋子卡扣斷裂、豆倉本體開裂、連接底座變形
維修：更換密封膠圈、修復卡扣、黏合/替換破裂豆倉、校正底座

Aged rubber seal, broken lid clip, cracked hopper, deformed base mount
Repair: New rubber gasket, fix clip, glue or replace hopper, realign base

馬達碳刷磨損、電壓供電不足、傳動機構阻力過大、刀盤卡殘粉
維修：更換馬達碳刷、檢查供電電路、拆解潤滑傳動齒輪、徹底清潔刀盤

Worn motor carbon brush, low voltage supply, high resistance drive, residual powder jam burr
Repair: Replace carbon brush, inspect power circuit, lubricate drive gear, full burr cleaning

刀盤嚴重磨損崩齒、軸承金屬磨損碎屑、螺絲鬆動脫落
維修：直接替換整套刀盤、更換軸承、全部螺絲加固鎖緊

Heavily worn broken burr, bearing metal debris, loose falling screws
Repair: Full burr set replacement, new bearing, retighten all fixing screws

計數光感感應器髒污、定量齒輪打滑、控制電路板參數偏移、電源波動
維修：清潔光感元件、替換計數齒輪、重校電路板定量參數、加穩壓供電

Dirty optical dose sensor, slipping dose gear, shifted circuit parameter, power fluctuation
Repair: Clean sensor, replace dose gear, recalibrate circuit, install voltage stabilizer

搖柄連接齒磨平、傳動螺絲滑牙、刀盤固定座鬆動
維修：重製傳動螺紋、替換搖柄齒輪、加固刀盤底座固定結構

Stripped crank gear, slipping drive screw, loose burr mount
Repair: Recut drive thread, replace crank gear, reinforce burr base

馬達線圈短路、電路板元件燒毀、散熱通道完全堵塞、長時間滿載運轉
維修：維修或更換馬達、替換燒毀電路板、全面拆解清潔散熱系統

Short motor coil, burnt circuit component, fully blocked vent, long continuous grinding
Repair: Fix or replace motor, swap burnt PCB, full cooling system deep clean

觸控面板排線脫落、顯示屏燒毀、主控板供電故障、按鍵彈片氧化
維修：重插排線、替換LCD面板、修復主控電路板、清潔或更換按鍵模組

Loose touch screen cable, burnt LCD, main board power fault, oxidized button spring
Repair: Reconnect cable, new LCD, repair main PCB, clean or replace button module

刀盤倉、粉道死角過多、缺少清潔刮片、油脂長期堆積
保養：每周完整拆解清潔；維修：加裝輔助清粉刮片、打磨機體內死角

Dead space in burr chamber & chute, missing wiper blade, long-term oil buildup
Maintain: Weekly full disassembly clean; Repair: Install wiper blade, polish internal dead corners

紅外感應頭髒污、感應電路損壞、豆倉安裝不到位斷開感應觸點
維修：清潔感應鏡頭、替換感應模組、校正豆倉安裝卡扣觸點

Dirty IR sensor lens, broken sensor circuit, misaligned hopper trigger contact
Repair: Clean sensor lens, replace sensor module, realign hopper trigger clip

底部防滑墊脫落老化、馬達軸心不平衡、刀盤組裝偏心、底座支架斷裂
維修：更換全套防滑防震墊、校正馬達平衡、重新對準刀盤、修復底座支架

Fallen aged anti-slip pad, unbalanced motor shaft, offset burr assembly, cracked base stand
Repair: New full anti-vibration pad set, balance motor, realign burr, fix base stand

放置環境潮濕、清洗後未完全晾乾、沿海霧氣鹽分腐蝕金屬件
保養：存放乾燥通風處，清潔後徹底吹乾；維修：除鏽拋光、替換重度生鏽刀盤與軸承

Humid storage, not fully dry after washing, coastal salt air corrosion
Maintain: Store dry ventilated area, fully air dry after clean; Repair: Rust polishing, replace heavily rusted burr & bearing

【每日保養】清潔出粉殘粉、擦拭豆倉；【每周保養】拆解刀盤刷除油脂；【每月保養】潤滑傳動齒輪、檢查螺絲鬆動；【季度保養】完整機體拆解除油除鏽
禁忌：不可用水直接沖洗馬達與電路板、不可使用粗糙金屬刷刮刀盤、不可長時間滿載連續研磨

Daily: Wipe chute residual powder & hopper; Weekly: Disassemble burr oil cleaning; Monthly: Lubricate drive gear, check loose screws; Quarterly: Full deep degrease & rust removal
Taboos: Never wash motor/circuit board with water, no rough metal brush on burr, avoid long continuous full-load grinding