專業維修咖啡研磨豆機 巴莱纳 Balena Professional Coffee Grinder Repair Balena All Series

故障原因：電源線斷裂、保險絲燒毀、開關損壞、馬達線圈燒毀、觸控面板故障。檢修流程：檢查供電→替換開關→測試馬達→更換保險絲/線路板。

Fault cause: Broken power cord, blown fuse, defective power switch, burnt motor coil, touch panel failure. Repair: Power check → switch replacement → motor testing → fuse/mainboard swap.

原因：傳動齒輪磨損、聯軸器斷裂、卡豆卡死、馬達軸卡死。處理：清潔卡豆、更換齒輪/連軸器、潤滑馬達軸。

Cause: Worn drive gear, broken coupler, stuck coffee beans, seized motor shaft. Fix: Clear jam, replace gear/coupler, lubricate motor shaft.

原因：磨盤缺油、金屬異物進入、軸承磨損、磨盤變形碰撞。保養：拆解清潔、替換軸承、校正磨盤間距。

Cause: Dry burrs, foreign metal objects, worn bearing, deformed burr collision. Maintenance: Disassemble clean, replace bearing, calibrate burr gap.

故障：調節齒條滑牙、刻度盤卡扣斷裂、調節螺絲滑絲。維修：更換調節機構、重新攻牙固定。

Fault: Stripped adjustment rack, broken dial clip, stripped screw. Repair: Replace adjustment assembly, re-thread fixing screw.

成因：咖啡油脂累積、濕氣結塊、出粉嘴變形。保養方案：定期高溫清潔、拋光出粉通道、加裝防靜電配件。

Cause: Coffee oil buildup, moisture clumping, deformed chute. Maintenance: Regular deep clean, polish chute, install anti-static part.

核心問題：磨盤鈍化、磨盤移位、軸承間隙過大。解決：打磨或更換刀盤、校正軸承間距。

Main issue: Dull burrs, misaligned burrs, excessive bearing play. Fix: Resurface or replace burrs, calibrate bearing clearance.

原因：腳墊老化、馬達不平衡、磨盤安裝歪斜、底座螺絲鬆脫。維修：更換減震墊、鎖緊固定螺絲、校正刀盤。

Cause: Worn rubber feet, unbalanced motor, tilted burr, loose base screws. Repair: New shock pads, retighten screws, align burrs.

商用機常見：計時模組故障、電磁閥卡滯、粉槽感應器髒污。處理：清洗感應器、替換計時板、維修下料閥。

Commercial common: Timer board fault, stuck solenoid valve, dirty sensor. Fix: Clean sensor, replace timer PCB, repair dosing valve.

橡膠密封墊硬化、豆倉卡扣斷裂、轉軸磨損。配件更換：全新密封圈、豆倉卡扣組件。

Hardened rubber seal, broken hopper clip, worn pivot. Parts swap: New seal ring, hopper clip assembly.

馬達散熱不良、風扇堵塞、過溫保護器損壞、長時間滿載研磨。維修：清潔散熱風道、替換溫控開關。

Poor motor cooling, blocked fan, faulty thermal cut-off, overloading. Repair: Clean vent, replace thermal switch.

面板進水受潮、排線鬆脫、主控板燒壞、屏幕背光損壞。檢修：乾燥機板、重插排線、更換觸控模組。

Water damage, loose ribbon cable, burnt main PCB, broken backlight. Repair: Dry circuit board, re-seat cable, replace touch module.

環境乾燥、出粉通道無防靜電設計、金屬部件接地不良。保養方案：加裝防靜電噴嘴、接地線維修。

Dry environment, no anti-static chute, poor grounding. Solution: Install anti-static nozzle, repair ground wire.

香港潮濕環境、長期殘留咖啡油脂、清洗後未完全風乾。處理：除鏽拋光、防鏽油保養、更換嚴重鏽蝕零件。

Hong Kong humid climate, leftover coffee oil, incomplete drying after cleaning. Fix: Rust removal polish, anti-rust lubrication, replace heavily rusted parts.

計時IC老化、電容鼓包、按鈕漏電。維修：替換電容、更換計時電路板。

Aged timer IC, swollen capacitor, leaky button circuit. Repair: Swap capacitors, replace timer PCB.

調節彈簧疲勞、固定螺絲自鬆、磨盤支架磨損。維修：更換彈簧、鎖緊防鬆螺絲、替換支架。

Fatigued adjustment spring, loose lock screw, worn burr holder. Repair: New spring, lock tight screw, replace holder.

下料通道堵塞、阻料片卡死、傳動聯軸完全斷裂。處理：徹底清潔下料道、更換聯軸器。

Blocked feed chute, stuck stopper, fully broken coupler. Fix: Deep clean feed path, replace coupler.

內部線路破皮、接地線脫落、電容漏電。安全維修：絕緣包裹線路、重接接地線、替換故障電容。

Damaged internal wiring, detached ground wire, leaky capacitor. Safe repair: Insulate wiring, reconnect ground, swap faulty capacitor.

光感應器髒污、感應線斷裂、感應板損壞。維修：清潔光感、重接線路、替換感應模組。

Dirty optical sensor, broken sensor wire, damaged sensor board. Repair: Clean sensor, rewire, replace sensor module.

磨盤永久鈍化、軸承卡死、馬達線圈燒毀、油路堵塞、電路板腐蝕。建議香港用戶每3個月做一次深度拆解保養。

Permanently dull burrs, seized bearing, burnt motor coil, blocked oil channel, corroded PCB. HK users recommended full disassembly maintenance every 3 months.

每日清潔出粉口、每周拆洗磨盤、存放乾燥通風處、長期不用清空豆倉、每年到店做一次除鏽潤滑保養。

Daily chute clean, weekly burr disassembly wash, store in dry ventilated area, empty hopper when idle, annual anti-rust lubrication service at shop.