專業維修咖啡研磨豆機 Galiwin 伽利略Q18、S17 Professional Coffee Grinder Repair Galiwin Q18 & S17

成因：電源線斷裂、開關燒毀、馬達保險熔斷、變壓器損壞、主板故障。維修方案：檢查供電線路、更換電源開關、重裝保險絲、維修/替換驅動主板。保養建議：避免長時間高負荷連續運轉。

Cause: Broken power cord, burnt switch, blown motor fuse, damaged transformer, main board failure. Solution: Rewire power line, replace power switch, reset fuse, repair or swap control board. Tip: Avoid long continuous heavy-duty use.

成因：咖啡豆卡夾、油脂積垢凝固、金屬異物掉入磨盤、調研磨度過細。維修：拆解清潔磨盤、取出異物、調整研磨刻度、更換磨盤墊圈。保養：每週清潔磨盤殘油。

Cause: Bean jam, solidified coffee oil, metal foreign object, ultra-fine grind setting. Solution: Disassemble & clean burrs, remove debris, adjust grind dial, replace burr gasket. Tip: Weekly burr degreasing.

成因：豆倉進料口堵塞、撥粉片老化、定量感應器故障、磨盤間隙偏移。維修：疏通進料通道、替換撥粉葉、校正定量模組、重新校準磨盤距離。

Cause: Hopper clog, worn dosing paddle, faulty dose sensor, misaligned burr gap. Solution: Clear feeding channel, replace paddle, calibrate dosing module, re-align burr gap.

成因：磨盤鈍化缺齒、磨盤固定螺絲鬆動、磨盤變形。維修：打磨/更換全新磨盤、鎖緊固定組件、校正磨盤平行度。

Cause: Worn blunt burrs, loose burr screws, deformed burr plates. Solution: Resurface or replace burrs, fasten fixing parts, calibrate burr parallelism.

成因：磨盤互相刮擦、軸承磨損、馬達軸偏心、異物卡入磨盤。維修：調整磨盤間距、替換軸承、校正馬達軸、清理異物。

Cause: Burr collision, worn bearing, eccentric motor shaft, trapped metal debris. Solution: Adjust burr gap, replace bearing, realign motor shaft, clear foreign objects.

成因：馬達過熱保護啟動、散熱孔堵塞、馬達線圈老化內阻過高。維修：清理散熱風道、更換馬達、加強散熱改造。

Cause: Motor overheat protection triggered, blocked vent, aged motor winding. Solution: Clean cooling vents, replace motor, upgrade heat dissipation.

成因：密封膠圈老化硬化、出粉通道裂縫、防飛粉擋片損毀。維修：更換全套密封膠圈、修補通道、替換防飛粉配件。

Cause: Hardened worn seal ring, cracked outlet tunnel, broken anti-spray baffle. Solution: Replace full set of gaskets, repair tunnel, swap anti-spray parts.

成因：豆倉卡扣斷裂、底座鎖扣彈簧失效、螺絲滑牙。維修：替換卡扣彈簧、重攻螺絲牙、更換豆倉底座。

Cause: Broken hopper clip, failed lock spring, stripped screw thread. Solution: Replace clip spring, re-tap thread, swap hopper base.

成因：面板受潮進水、觸控板線路氧化、主板觸控晶片損壞。維修：除濕清潔線路、修復觸控模組、替換控制主板。

Cause: Water moisture on panel, oxidized touch circuit, damaged touch IC. Solution: Dehumidify circuit, repair touch module, replace main control board.

成因：光感應器髒污/損壞、定量編碼器故障、主板計數程式異常。維修：清潔感應器鏡頭、替換編碼器、重刷主板程式。

Cause: Dirty/broken optical sensor, faulty encoder, abnormal main board program. Solution: Clean sensor lens, replace encoder, reflash main firmware.

成因：馬達負荷過大、散熱通道堵塞、連續研磨超時。維修：疏通散熱、檢查磨盤卡滯問題、更換老化馬達。保養：商用機每40分鐘休息5分鐘。

Cause: Overloaded motor, blocked air vent, over-long continuous grinding. Solution: Clear vents, check burr jam, replace aged motor. Tip: Commercial units rest 5 mins every 40 mins.

成因：咖啡油脂凝固卡緊調節齒輪、螺絲生鏽、調節軸變形。維修：拆解除油清潔齒輪、除鏽潤滑、校正調節軸。

Cause: Solidified coffee oil locking gears, rusted screw, deformed adjustment shaft. Solution: Disassemble & degrease gears, anti-rust lubrication, realign shaft.

成因：馬達線圈短路、電線破皮接地、主板受潮短路。維修：絕緣測試、替換短路馬達、更換內部配線。

Cause: Short-circuited motor winding, cracked wire insulation, damp main board short. Solution: Insulation test, replace short motor, rewire internal cables.

成因：出粉通道死角多、撥粉片設計老化、未定期清潔。保養方案：每日收工清潔出粉口，每週全拆磨盤除油，每月深度拆解內部通道。

Cause: Dead corners in outlet tunnel, worn dosing paddle, lack of regular cleaning. Maintenance: Daily outlet wipe, weekly burr degrease, monthly full disassembly deep clean.

成因：咖啡豆油脂黏附倉壁、進料口收縮變形、內部擋片阻礙。維修：熱水洗淨豆倉、整形進料口、調整內部導豆片角度。

Cause: Coffee oil stuck on hopper wall, deformed feeding throat, blocking internal baffle. Solution: Hot water wash hopper, reshape inlet, re-angle bean guide plate.

成因：馬達線圈過熱燒毀、電線塑膠外皮融化、磨盤高溫焦化殘粉。維修：立即停機檢查馬達、更換燒毀配線、全機深度除焦。

Cause: Burnt motor winding, melted cable insulation, charred stale powder on burrs. Solution: Power off immediately, inspect motor, replace burnt wiring, full carbon removal clean.

成因：磨盤積油、軸心生鏽、調節過緊。維修：拆解清洗磨盤、軸心除鏽潤滑、重新調整研磨間距。

Cause: Oily burrs, rusted spindle, overly tight grind gap. Solution: Disassemble & wash burrs, anti-rust lubricate spindle, reset grind gap.

成因：半導體製冷片損壞、溫度感測器故障、散熱風扇停轉。維修：替換製冷模組、更換溫感、修復散熱風扇。

Cause: Broken thermoelectric cooling chip, faulty temp sensor, failed cooling fan. Solution: Replace cooling module, swap temperature probe, repair fan unit.

成因：過載保護鎖定、主板程式崩潰、電源供應器燒毀。維修：解除保護鎖、重刷韌體、替換開關電源。

Cause: Overload protection lock, firmware crash, burnt power supply unit. Solution: Unlock protection, reflash firmware, replace PSU.

成因：香港高濕氣候、機器內部殘留水氣、清潔後未徹底風乾。維修：除鏽拋光金屬件、密封防鏽處理、更換嚴重鏽蝕零件。保養：每日清潔後完全風乾再收機。

Cause: High Hong Kong humidity, trapped moisture inside, incomplete drying after cleaning. Solution: Rust removal & polishing, anti-rust sealing coating, replace heavily corroded parts. Tip: Fully air-dry after daily cleaning.