保養期過後維修澳格思分體恆濕雪茄櫃｜冷濕雙系統失準、濕度長期偏低雪茄乾裂
作者：香港駿弘電器維修公司
浏览：
发表时间：2026-06-28 14:47:17
專業維修工具設備 Professional Repair Tools & Equipment
圖片1：雪茄櫃濕度檢測儀替換URL
圖片2：冷凍系統壓力測試機替換URL
圖片3：恆濕主板維修儀替換URL
圖片4：密封膠條拆裝工具替換URL
雪茄櫃最常壞20個故障Q&A（香港家用/商用通用） 20 Common Cigar Humidor Faults Q&A (HK Residential & Commercial)
1. 澳格思分體雪茄櫃濕度長期偏低，雪茄乾裂
1. Oasis split cabinet long-term low humidity, cracked cigars
成因：濕度感應器老化、加濕模組堵塞、冷濕雙系統參數失準、密封膠條漏氣。維修方案：更換高精度濕度探頭、清洗加濕蒸發器、重新校正雙系統恆濕程式、替換老化門封。
Cause: Aged humidity sensor, blocked humidifier module, dual system parameter offset, leaky door seal. Solution: Replace high-precision sensor, clean evaporator, recalibrate humidity program, renew rubber seal.
2. 冷濕雙系統溫濕度數值嚴重失準，顯示與實際差距大
2. Dual cooling-humidity system reading deviation, big gap between display & real value
成因：主控主板程序偏移、溫濕度探頭積灰受潮、分體機連接線路接觸不良。維修：主板重新刷寫標準參數、清潔探頭、重接加固內部線路。
Cause: Main board program drift, dusty damp sensor, loose wiring of split unit. Solution: Rewrite factory parameters, clean sensor, re-fix internal wiring.
3. 雪茄櫃內部漏水，底部積水浸濕雪茄
3. Internal water leakage, pool water soak cigars
成因：排水孔堵塞、蒸發盤破裂、冷凝管脫落、門封凝露滴水。維修：疏通排水管路、更換蒸發盤、固定冷凝管、更換門封減少凝露。
Cause: Blocked drain hole, cracked evaporate tray, detached condensate pipe, dew leak from seal. Solution: Clear drain, replace tray, fix pipe, renew seal.
4. 機器正常運轉但完全不製冷，溫度持續升高
4. Unit running but no cooling, temperature keep rising
成因：雪種洩漏、壓縮機故障、風扇馬達停轉、冷凝器積灰散熱不良。維修：檢測雪種管路補漏加雪種、維修/更換壓縮機、替換循環風扇、深度清洗冷凝器。
Cause: Refrigerant leak, compressor breakdown, fan motor stall, dusty condenser. Solution: Leak test & refill gas, repair compressor, replace circulation fan, deep clean condenser.
5. 濕度長期過高，雪茄發霉、櫃內生銹
5. Excess high humidity, mold on cigars & cabinet rust
成因：除濕模組故障、主板控濕邏輯損壞、通風口堵塞。維修：維修除濕系統、修復主控板、疏通內部循環風道。
Cause: Dehumidifier module fault, broken control logic, blocked air vent. Solution: Repair dehumidify system, fix mainboard, unclog air duct.
6. 分體機室內機與室外機無法連動，一邊運轉一邊停機
6. Split unit indoor & outdoor out of sync, one run one stop
成因：通訊線斷路、變頻模組損壞、分體控制板不匹配。維修：更換通訊線、維修變頻驅動板、重新配對內外機程式。
Cause: Broken communication wire, damaged inverter module, mismatched split control board. Solution: Renew wire, repair inverter, re-pair indoor & outdoor unit.
7. 開機後發出異常震動噪音，運轉聲巨大
7. Abnormal vibration & loud noise after startup
成因：風扇葉片變形、壓縮機腳膠老化、管路共振、內部支架鬆動。維修：校正/更換風扇、更換減震膠、固定管路與金屬支架。
Cause: Deformed fan blade, aged compressor damper, pipe resonance, loose bracket. Solution: Replace fan, renew damper, fasten pipes & frames.
8. 觸控屏幕黑屏、按鍵無反應，無法調溫濕度
8. Touch screen black, button no response, cannot adjust temp/humidity
成因：顯示面板線路斷裂、觸控IC燒毀、供電變壓器故障。維修：維修面板線路、替換觸控模塊、更換變壓器穩壓供電。
Cause: Broken display wire, burnt touch IC, faulty power transformer. Solution: Fix wiring, replace touch module, renew transformer.
9. 門關緊後仍漏冷氣，溫濕度無法穩定維持
9. Cold air leak even with closed door, unstable temp & humidity
成因：磁吸門封老化變形、門鉸鏈鬆動、門體變形。維修：全新替換磁吸膠條、調校鉸鏈、校正門體平整度。
Cause: Deformed magnetic seal, loose hinge, warped door frame. Solution: New magnetic seal, adjust hinge, straighten door frame.
10. 加濕系統不出水霧，恆濕功能失效
10. Humidifier no mist output, humidity function disabled
成因：超音波震動片結水垢、進水濾網堵塞、加濕水泵損壞。維修：除水垢清洗震動片、更換濾網、維修供水泵。
Cause: Limescale on ultrasonic chip, blocked inlet filter, broken water pump. Solution: Descaling chip, replace filter, repair pump.
11. 除濕模組不停運轉，耗電量暴增
11. Dehumidifier run nonstop, high power consumption
成因：濕度探頭誤判、繼電器卡死、主板控製邏輯故障。維修：替換感應器、更換繼電器、重寫主板控溫濕程式。
Cause: Misread humidity sensor, stuck relay, broken mainboard logic. Solution: Replace sensor & relay, reprogram control board.
12. 分體室外機無法啟動，室內機只吹常溫風
12. Outdoor split unit fail to start, indoor only blow room temp air
成因：室外機電容燒毀、啟動繼電器故障、散熱風扇卡死。維修：更換壓縮機電容、維修啟動電路、清理風扇葉片。
Cause: Burnt compressor capacitor, faulty start relay, stuck cooling fan. Solution: Replace capacitor, repair circuit, clean fan blade.
13. 櫃內出現異味，雪茄吸附難聞氣味
13. Strange odor inside cabinet, cigars absorb bad smell
成因：蒸發器發霉、濾網長期未更換、排水盤滋生細菌。維修：深度高溫殺菌清洗內循環系統、替換活性炭過濾網、消毒排水盤。
Cause: Moldy evaporator, expired filter, bacteria in drain tray. Solution: High temp disinfection clean, new carbon filter, sanitize tray.
14. 溫度無法調低，最低只能維持22度以上
14. Cannot lower temperature, minimum stay above 22°C
成因：雪種不足、冷凝器散熱差、溫度感應器偏移。維修：查漏補充雪種、清洗散熱器、校正溫度探頭。
Cause: Low refrigerant, poor condenser cooling, offset temp sensor. Solution: Refill gas, clean radiator, calibrate sensor.
15. 內部循環風扇時轉時停，溫濕度不均勻
15. Circulation fan intermittent stop, uneven temp & humidity
成因：風扇馬達碳刷磨損、風扇供電線接觸不良、風扇驅動板故障。維修：更換馬達碳刷、加固線路、維修驅動板。
Cause: Worn fan carbon brush, loose power wire, broken fan driver board. Solution: Replace brush, fix wiring, repair driver.
16. 機器自動斷電重啟，無法穩定持續運行
16. Auto power cut & restart, unstable operation
成因：供電穩壓器損壞、主板短路、線路受潮漏電。維修：更換穩壓電源、修復短路線路、內部除濕絕緣處理。
Cause: Broken power stabilizer, short circuit mainboard, damp wiring leakage. Solution: New power supply, fix short circuit, insulation dehumidify treatment.
17. 密碼鎖/電子門鎖失靈，無法開啟雪茄櫃門
17. Electronic lock failure, cannot open cabinet door
成因：鎖控模塊無供電、電子鎖馬達損壞、密碼程序亂碼。維修：修復鎖體供電、替換電子鎖、重置密碼系統。
Cause: No power to lock module, broken lock motor, corrupted password program. Solution: Fix power supply, replace lock, reset password system.
18. 分體機連接銅管結霜結冰，製冷效率大幅下降
18. Split copper pipe frost & ice, low cooling efficiency
成因：雪種過量、保溫棉破損、風量不足。維修：調整雪種容量、重新包裹保溫棉、疏通風道提升循環風量。
Cause: Overfilled refrigerant, broken insulation foam, low air flow. Solution: Adjust gas volume, re-wrap foam, unclog air duct.
19. 恆濕記憶設定無法保存，重開機參數重置
19. Humidity memory setting lost, reset after power off
成因：主板儲存電池耗盡、記憶晶片損壞。維修：更換主板備用電池、替換記憶IC晶片。
Cause: Dead mainboard backup battery, damaged memory chip. Solution: Replace battery & memory IC.
20. 保養期過後廠商報價昂貴，整機更換成本高
20. High official out-of-warranty repair quote, costly full unit replacement
我們專做零件維修，無需更換整機，針對澳格思分體恆濕雪茄櫃冷濕雙系統獨立維修校正，價格比原廠維修便宜40%-60%，提供3個月維修保固，環保維修減少電子廢棄物。
We only repair faulty parts instead of full unit replacement, independent calibration for Oasis dual cooling-humidity system, price 40%-60% lower than official service, 3-month repair warranty, eco-friendly service reduce e-waste.
標準維修順序流程 Standard Repair Procedure
1
電話/WhatsApp遠程診斷故障
Remote fault diagnosis via Call / WhatsApp
客戶描述症狀，初步判斷故障零件、報價
Client describe issue, initial fault & quotation assessment
2
上門檢測全機冷濕雙系統
On-site full dual system inspection
濕度、溫度、雪種、主板、風扇、管路全面測試
Full test for humidity, temp, refrigerant, mainboard, fan, pipe
3
確認故障，客戶確認維修報價
Confirm fault & quotation with client
不強制維修，報價透明無隱藏收費
No compulsory repair, transparent pricing no hidden cost
4
零件維修/更換、系統校正
Part repair / replacement & system calibration
冷濕雙系統重新標校，還原出廠恆濕參數
Recalibrate dual system back to factory humidity standard
5
24小時機器穩定測試
24 hours stability running test
觀察溫濕度波動，確保無復發故障
Monitor temp & humidity fluctuation to avoid recurring fault
6
交付+3個月維修保固
Delivery + 3-month repair warranty
提供保固單，後續免費電話跟進保養建議
Warranty document provided, free follow-up maintenance advice
環保維修服務電器種類 Eco-Friendly Appliance Repair Service List
熱水爐、冰箱、電磁爐、紅酒櫃、雪茄櫃、抽真空機、抽濕機、電飯煲、煮食爐、焗爐、蒸焗爐、抽油煙機、吹風機、直發夾
專修雪茄櫃品牌｜全系列電器維修品牌 Cigar Humidor Brands & All Supported Appliance Brands
完整支援品牌：維諾卡夫、芭克斯、哈士奇、西門子、美的、海爾、卡薩帝、索菲亞、新朝、富客、electrolux伊莱克斯、德国宝Asko、Baumatic、Bosch、Candy 金鼎、Canopus 肯特、Comfee、Fisher & Paykel 飛雪、Fujira 日本富士樂、Gaggenau、Gala 家麗牌、German Home、Hitachi 日立、Kaneda 金田、LG 樂金、MI 小米、Midea、Panasonic 樂聲、Philco 飛歌、Rasonic 樂信、Samsung 三星、Sharp 聲寶、Siemens 西門子、Smeg、Speed Queen、Summe 德國卓爾、Thomson、Toshiba 東芝、V-Zug、Vestel、Whirlpool 惠而浦、White-Westinghouse 威士汀、Zanussi 金章、FOTILE 方太、米卡Mia Cucina、苏泊尔SUPOR、老板Robam、德玛仕DEMASHI、志高CHIGO、乐创Lecon、卡士Couss、UKOEO、海氏Hauswirt、长帝Changdi
香港全區上門維修服務地區 HK Wide Coverage On-Site Service Area
香港島
Hong Kong Island
中西區：中環、上環、西營盤、堅尼地城、山頂
灣仔區：灣仔、銅鑼灣、跑馬地、大坑、會展
東區：北角、鰂魚涌、筲箕灣、柴灣
南區：香港仔、鴨脷洲、深水灣、淺水灣、赤柱
Central & Western: Central, Sheung Wan, Sai Ying Pun, Kennedy Town, Peak
Wan Chai: Wan Chai, Causeway Bay, Happy Valley, Tai Hang, Wanchai Convention
Eastern: North Point, Quarry Bay, Shau Kei Wan, Chai Wan
Southern: Aberdeen, Ap Lei Chau, Deep Water Bay, Repulse Bay, Stanley
九龍
Kowloon
油尖旺：油麻地、尖沙咀、旺角
深水埗：深水埗、長沙灣、荔枝角
九龍城：九龍城、九龍塘、何文田、紅磡
黃大仙：黃大仙、慈雲山、樂富、新蒲崗
觀塘：觀塘、藍田、將軍澳
Yau Tsim Mong: Yau Ma Tei, Tsim Sha Tsui, Mong Kok
Sham Shui Po: Sham Shui Po, Cheung Sha Wan, Lai Chi Kok
Kowloon City: Kowloon City, Kowloon Tong, Ho Man Tin, Hung Hom
Wong Tai Sin: Wong Tai Sin, Tsz Wan Shan, Lok Fu, San Po Kong
Kwun Tong: Kwun Tong, Lam Tin, Tseung Kwan O
新界
New Territories
荃灣：荃灣、馬灣
屯門元朗：元朗、天水圍
北區：上水、粉嶺、打鼓嶺
大埔：大埔墟、船灣淡水湖
沙田：沙田、大圍、馬鞍山
西貢：西貢市、將軍澳
Tsuen Wan: Tsuen Wan, Ma Wan
Tuen Mun & Yuen Long: Yuen Long, Tin Shui Wai
North: Sheung Shui, Fanling, Ta Kwu Ling
Tai Po: Tai Po Market, Plover Cove
Sha Tin: Sha Tin, Tai Wai, Ma On Shan
Sai Kung: Sai Kung Town, Tseung Kwan O
客戶維修好評個案 Customer Repair Testimonials
★★★★★
澳格思分體雪茄櫃濕度長期偏低，雪茄乾裂，師傅上門校正冷濕雙系統，現在濕度穩定70%，價格比原廠平一半，推薦！
Oasis split humidor low humidity crack cigars, technician recalibrate dual system, stable 70% humidity now, price half cheaper than official service, highly recommend!
★★★★★
商用雪茄櫃漏水，底部積水，一日內上門維修，疏通排水更換蒸發盤，運行三個月無問題。
Commercial cigar cabinet water leakage, same day on-site repair, clear drain & replace tray, no fault for 3 months.
★★★★★
保養期過後西門子紅酒櫃不製冷，不換整機只修壓縮機，節省大量開支，服務覆蓋新界沙田。
Out-of-warranty Siemens wine cabinet no cooling, repair compressor instead of full unit, save big cost, service cover Sha Tin NT.
★★★★★
觀塘門店交機維修，師傅專業，24小時測試穩定，WhatsApp回覆即時，電話55311921。
Drop off repair at Kwun Tong workshop, professional tech, 24h stability test, instant WhatsApp reply, hotline 55311921.
★★★★★
香港島淺水灣家用澳格思雪茄櫃觸控黑屏，一日修復，提供三個月保固，態度友善。
Repair Oasis touch screen black at Repulse Bay HK Island, fixed within 1 day, 3-month warranty, friendly service.
