駿弘電器維修 German Pool 專業維修

多為電源保險絲燒斷、電源板變壓器損壞、插座接觸不良，檢查供電更換電源板即可修復。

Usually caused by blown fuse, damaged power board transformer, poor socket contact. Check power supply and replace power board.

多是溫度傳感器異常、線圈盤溫度過高、散熱風扇卡死，更換熱敏電阻清理風道就能解決。

Usually temperature sensor abnormality, coil overheating, cooling fan stuck. Replace thermistor and clean air duct.

散熱不良、風扇轉速不足、面板過熱保護啟動，清理油污灰塵更換散熱風扇恢復正常。

Poor heat dissipation, insufficient fan speed, overheat protection. Clean grease and replace cooling fan.

觸摸按鍵板受潮老化、控制面板排線鬆動，更換觸摸按鍵面板重插排線即可。

Touch panel moisture damage, loose control cable. Replace touch panel and reconnect cable.

大功率 IGBT 功率管燒毀、諧振電容損壞、線圈盤老化，更換功率管與配套電容修好。

IGBT power tube burned, resonant capacitor damaged, coil aging. Replace power tube and matching capacitor.

內部風扇軸承磨損、機體鬆動、線圈盤鬆動，更換靜音風扇緊固內部配件消除異音。

Internal fan bearing wear, loose body, loose coil. Replace silent fan and tighten internal parts.

加熱管燒毀、溫控器斷路、高溫安全保險跳斷，更換發熱管與復位溫控即可修復。

Heating element burned, thermostat broken, high temperature safety fuse tripped. Replace heating element and reset thermostat.

水流量感應器靈敏度下降、進水壓力不均、恆溫主板失靈，清洗水流開關或調節水壓。

Water flow sensor reduced sensitivity, uneven water pressure, thermostat board failure. Clean flow switch or adjust water pressure.

機體積塵散熱差、超溫保護啟動、熱熔保險老化，清理內部灰塵更換過熱保護配件。

Dust accumulation, poor heat dissipation, overheat protection activated, thermal fuse aging. Clean dust and replace overheat protection parts.

觸控面板受潮進水、控制面板排線鬆動、顯示板故障，吹乾內部潮氣更換按鍵板。

Touch panel water damage, loose control cable, display board failure. Dry internal moisture and replace button board.

進出水接頭膠圈老化、水箱接口鬆動、內部水管破損，更換密封圈重新緊固管路。

Inlet/outlet connector rubber ring aging, loose tank interface, internal water pipe damage. Replace sealing ring and retighten pipes.

溫度探頭損壞、水流不足、主板電路異常，檢查熱敏探頭與進水流量，更換故障傳感器。

Temperature probe damaged, insufficient water flow, mainboard circuit abnormality. Check thermal probe and water flow, replace faulty sensor.

內部水垢堵塞蒸氣喉管、水泵故障或水箱未到位。水垢輕微可用檸檬酸 / 白醋清洗；嚴重需疏通喉管或更換水泵、水箱感應器。

Limescale clogging steam pipe, faulty water pump or improperly inserted water tank. Minor limescale can be cleaned with citric acid/vinegar; severe cases require unclogging or replacing pump/tank sensor.

爐腔 / 蒸發盤溫度過高、溫度傳感器短路或散熱不良。清理风道、檢查傳感器線路，損壞需更換熱敏電阻。

Oven cavity/evaporation tray overheating, temperature sensor short circuit or poor ventilation. Clean air duct, check sensor wiring; replace thermistor if damaged.

水箱密封圈老化、水位感應器故障或進水管鬆脫。更換密封圈、重插水管，感應器損壞需更換水位開關。

Worn tank seal, faulty water level sensor or loose inlet pipe. Replace seal, reinsert pipe; replace level switch if sensor fails.

門鉸鬆動、密封膠圈老化或門體變形。調整鉸鏈、更換高溫密封條，變形需校正門體。

Loose door hinge, worn seal gasket or door deformation. Adjust hinge, replace high-temperature seal; correct door if deformed.

觸控面板受潮、排線鬆動或主板故障。吹乾內部潮氣、重插排線，損壞需更換控制面板 / 主板。

Touch panel moisture damage, loose cable or mainboard failure. Dry interior, reconnect cables; replace control panel/mainboard if damaged.

散熱風扇軸承磨損、風葉鬆動或內部配件鬆脫。更換靜音風扇、緊固風葉及內部組件。

Worn cooling fan bearing, loose fan blade or internal parts loose. Replace silent fan, tighten blade and internal components.